TSL - Technology

Think big, print bigger With its bigger build volume, the Ultimaker S5 is designed for a reliable 3D printing experience at scale. For large, technical prints, Tough PLA material offers toughness similar to ABS with the simplicity of PLA. Optimized materials Ultimaker materials are extensively tested to give the best results on the Ultimaker S5. And Ultimaker Cura software comes with preconfigured profiles, so you don't need to spend time on complex slicing settings. Limitless possibilities 3D print everything from quick prototypes to complex, technical parts with Ultimaker's range of build and support materials. And with an open filament system, you can also choose a custom material solution.

The Ultimaker 2+ Connect builds upon the award-winning benchmark of its predecessor, to add intuitive operation and deeper software connectivity. • Build volume: 223 x 220 x 205 mm (8.7 x 8.6 x 8 inches) • Network connectivity via Wi-Fi or Ethernet enables remote printing over the cloud with added security • Easy control with the 2.4-inch colour touchscreen • Single extrusion

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

The R25 is an industrial quality plastic granulator. Suitable materials for recycling include PP, HIPS, ABS and LDPE. Materials to be granulated are loaded into the hopper at the top of the machine. A combination of static and rotating blades gradually chops the material into smaller and smaller pieces. Once the material reaches a small enough size it passes out through a mesh filter and into a collection bin. The cutting blades are powered by a three phase motor fitted with a phase inverter, allowing operation from a normal 230V electrical supply. When not in use, a lockable cover can be fitted over the inlet chute, ensuring that no unwanted debris enters the machine. The Process: Wash out your old cartons Shred them in the R25 Schredder, reducing their volume by 95% and creating a usable material. At this stage, you can choose to put the waste for normal recycling, or to re-process it within school, in either of two ways: Use it directly in the CR Clarke 25 Injection Moulding Machine. (490-170) Heat it on a mould-plate and then roll it into a new sheet using the R30 Sheet Press (490-048).

The R30 Sheet Press converts granulated thermoplastic material into a usable form using heat and pressure. As standard, the formed article is a flat plastic sheet, which can typically be used for vacuum forming, laser cutting, line bending etc. There are also tools available for making shaped parts, for example Frisbees, on the machine. A removable material cassette is loaded with granules of the material to be pressed. For best results the granules are sprinkled uniformly over the base of the cassette. The cassette is then loaded into the R30 sheet press, and clamped firmly between two temperature controlled aluminium hotplates. The heat and pressure causes the material granules to soften and fuse. At the end of the pressing cycle, the material cassette is unloaded and allowed to cool. The formed sheet of material can then be removed and used. As standard the R30 produces a sheet 457 x 305mm (compatible with the 725FLB vacuum former).

• Auto sensing voltage (90-257v) for global use • Closed loop automatic fl ow control • DeepPleat DUO pre fi lter • Reverse fl ow • Easi-Seal filter location • Small footprint and low noise levels • Enhanced fi lter system • Auto cut off • Filter full indicators • Mobile with heavy duty castors IQ System The BOFA Oracle extractor is now available with the new revolutionary IQ operating system. Users benefi t from the ease of operation and clarity of real time information, the system also provides a cache of analytical data enabling users to download performance and operating parameters for evaluation purposes. • High Quality, High Contrast LCD Display • Clear and Simple Real Time Features • Airfl ow Reading and Set Point • Real Time Airfl ow Reading in CFM or M3/hr • Filter Condition Monitoring with Alarm and Warning • Temperature Monitoring • Run Hours • Extraction Running Indicator • Hose Blocked Warning • Unit Failure and Door Open Alarm

High-performance fume extractor with ihgher capacity for larger laser cutters. The AD1000 packs a powerful range of unique features into one compact unit. • iQ operating system which provides real time filter monitoring, airflow reading, temperature monitoring, running time and block hose warnings • Closed loop automatic flow control • DeepPleat DUO pre filter • Reverse flow • Easi-Seal filter location • Small footprint and low noise levels • Enhanced filter system • Auto ct off • Mobile with heavy duty castors • Onboard compressor • interface with our laser cutters for automatic start and stop

All of our laser packages are supplied complete with everything required for a complete educational solution including recirculatory extraction unit, connection kit, design software. We also provide flexible training solutions with onsite installation and training or additional training sessions should you require a 'top-up.' • QSM (Quality Speed Mode) maintains 100% engraving quality while operating at maximum speed • Patented SmartACTTM motion control technology increases your productivity by reducing ramping process and job running time • Drag and engrave feature assures remarkably easy and fast set-ups • High speed DC motor runs up to 80ips for precise and rapid movement of the laser carriage • Reliable DuraGuide motion system with reinforced Kevlar belt delivers superb output quality • This machine is fi tted with the Smart Guard Fire Alarm and auto-cut out on extraction failure as standard WARRANTY INFORMATION 3 year machine warranty, 15 month tube warranty

Guard for HSM300 Disc Sander

Weight 13kg Height 880mm - effective table working height for Multicut-1 1040mm, Multicut-2S/SEV 1080mm. Suitable for: Multicut-1, Multicut-2S, Multicut-SE, Multicut-QUICK. Not suitable for the Hegner Polycut-3 and Multicut-2 scrollsaws Bolts used to fix multicut to stand are incuded with the machine and also with the stand. They are 3 x M8x16mm hex head & M8 sprung washer. Height 880mm - effective table working height for Multicut 1 1040mm, Multicut 2S 1080mm. Top size (triangular 450 x 445 x 445 mm)

The standard equipment for the DS 430S has the same specifications as the DS 430 on page 133, except for the Brazing Equipment which is listed below right. BRAZING STANDARD EQUIPMENT • 1 asbestos-free heat resistant refractory hearth • 2 full size heat reflective blocks • 4 half size heat reflective blocks • Push button no volt release starter (requires manual restart after power failure) • 1 RF 80 brazing torch

• Easy and safe to use in a general classroom environment requiring only a standard 13amp 230VAC socket. • Does not require a separate extraction system. • Cool to the touch as its unique cooling system keeps the entire casing cool. • Fully operational in approx. 15 minutes. • Thermostatically controlled without manual intervention at either 250°C or 150°C. • Designed to use lead-free metals including pewter (which melts at approx. 245°C) and also a lower melting point alloy (at approx. 137°C). • Internal melting pot has a clearly labelled swivel lid for observing the state of the molten metal and adding new material. • Moulds manufactured in vulcanised rubber, MDF, soap, woods, cuttle fish and many other materials are suitable. • Lesson plans are simple. • Risk assessment is clear. Supplied with: • 1 x Vulcanised Rubber Mould, Mould Holder and Clip • 5 x Sticks of Lead-Free Pewter (120-116) which are pre-melted into the melting pot ready for use. • Selector Switch for High/Low Temperature Control • Spill Tray

Grade 7 14 tpi Size: 1.25 x 0.46mm Pack 144

Grade 9 14 tpi Size: 1.43 x 0.5mm

All of our laser packages are supplied complete with everything required for a complete educational solution including recirculatory extraction unit, connection kit, design software. We also provide flexible training solutions with onsite installation and training or additional training sessions should you require a 'top-up.' • Popular all round laser engraver with stable and satisfactory performance • Intuitive control panel allows easy operations • Low maintenance motion system • Emergency button and key-switch add an extra layer of safety WARRANTY INFORMATION 24 months machine and laser tube warranty. Additional 12 months warranty on machine and laser tube is available.

All of our laser packages are supplied complete with everything required for a complete educational solution including recirculatory extraction unit, connection kit, design software. We also provide flexible training solutions with onsite installation and training or additional training sessions should you require a 'top-up.' • Popular all round laser engraver with stable and satisfactory performance • Intuitive control panel allows easy operations • Low maintenance motion system • Emergency button and key-switch add an extra layer of safety WARRANTY INFORMATION 24 months machine and laser tube warranty. Additional 12 months warranty on machine and laser tube is available.

Grade 12. Pack of 144. TPI: 23.

Grade 5 Hardwood to 1, Softwood to 1 1/4, 30 TPI

Grade 5 17 tpi Size 1.08 x 0.38mm Pack 144

Grade 6 14 tpi Size 1.20 x 0.38mm Pack 144

Grade 12 12.5 tpi Size: 1.85 x 0.6mm

HSS-R roll forged 4341 high speed steel 'jobber' bits. Manufactured to DIN338 with 118° point. For drilling steel, aluminium, non-ferrous metals, plastics and wood. Use cooling agent and drill at slow speeds for best results in metals. Sizes 1 - 13mm in 0.5mm increments. Metal storage case.

19 Pcs Jobber Drill Set - 1mm - 10mm in 0.5mm increments. General-purpose drill, to drill steels with tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite.

High speed steel. Straight shank. Right hand cutting. DIN 338/BS 328. Supplied in metal case.

Straight shank. The Precision Ground Jobber drills are of the best quality and the most dimensionally accurate. The Roll Forged Jobber drills are claimed to be more flexible giving greater resistance to breakage than. Precision Ground Jobber drills.

General-purpose drill, to drill steels with tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Size: 4mm Flute length: 43mm Length: 75mm

This alloy steel drill has a steeper twist and a deeper flute than HSS bits for rapid clearance of waste. Ideal for use in dowelling jigs. This Faithfull Lip & Spur Wood Drill Bit has the following specification: • Diameter: 6mm. • Working Length: 52mm. • Overall Length: 92mm.

General-purpose drill, to drill steels with tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Size: 2mm Flute length: 24mm Length: 49mm

Contains: • 51 HSS titanium-coated drill bits • 42 black finished HSS drill bits • 14 masonry • 18 wood-boring drill bits • 3 pilot drill bits • 47 screwdriver bits • 10 nut drivers • 3 drill stoppers • 4 holesaws • 1 holesaw adaptor • 3 cupped nail sets • 3 screw finders • 1 centre punch • 1 countersink • 1 drill gauge • 1 bit holder and 1 hex key

General-purpose drill, to drill steels with tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Size: 5mm Flute length: 52mm Length: 86mm

Latching emergency stop switch, red with yellow body, for foot/knee/palm.

Designed to cut a wide variety of timber and abrasive material such as MDF and plywood. With careful handling and under normal conditions, they will outlast HSS grade cutters many times. These top quality cutters will ensure an excellent finish and provide the user with long lasting and reliable service. • 1/4in Shank • Cutting Diameter: 6.0 mm 15/64in. • Cutting Length: 16 mm. • Shank Diameter: 1/4in.

Spare inserts for lathe tool 1/2inch

Tungsten Carbide tips ensure long life and the storage case provides a safe place to store the bits when they are not being used. Different cutter shapes enable the creation of a variety of profiles, grooves and mouldings in softwoods, hardwoods, MDF or plywood. Shank: 6.3mm (1/4in). Contains: 1 x Dovetail: 12.7 x 13mm 1 x Straight: 6 x 20mm 1 x Straight: 12 x 20mm 1 x Straight: 16 x 20mm 1 x Flush Trim: 12.7 x 13mm 1 x Rounding Over: R7.9mm, 25 x 14mm 1 x Rounding Over: R9.5mm, 28 x 14mm 1 x Roman Ogee: R4mm, 25 x 12mm 1 x Core Box: R6.3mm, 12.7 x 10mm 1 x Cove: R6.3mm, 22 x 12mm 1 x 45° Chamfer: 32 x 13mm 1 x 90° V-Groove: 12.7 x 9mm

General-purpose drill, to drill steels with tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Size: 6mm Flute length: 57mm Length: 93mm

A strong rigid plastic push stick suitable for use with many machines. An essential safety aid for use on any machine with an exposed cutting blade. Length 420mm Height 70mm (At highest point) Width (At widest point) 10mm Weight 150g

• 5 piece set • Available in a range of different sizes - 6mm, 8mm, 10mm, 12mm or 16mm • Lathe tools complete with replaceable tips • Also included are tip removal tools and spare screws to replace tips • Supplied in wooden storage case

A choice of bar type or precision adjustment hardened sliding jaw type.

The use of Trefolex will increase the life of taps and dies. It will also improve the quality of threads and reduce the effort required to cut them.

Circular die stock for 13/16inch O.D dies.

Fire Brick measuring 9 x 4.5 x 3inch

Mitre block 9inch long beech construction with accurate slots. RST.

For Second or Plug Taps please add an S or P to the catalogue number. Taper Taps will be supplied unless otherwise requested.

For Second or Plug Taps please add an S or P to the catalogue number. Taper Taps will be supplied unless otherwise requested.

As a box pan folder, a unique feature of this model for forming box ends is the use of standard steel angle cut as required for work clamping rather than conventional segments. A narrow bed assures that return bends are made with the workpiece suspended insude the folder. • Interrupted folds • Return bends • Box ends • Brackets and channels • Scrolls and cylindrical shapes

Floor stand for Gabro BF620.

13/16inch O.D.

13/16inch O.D.

For Second or Plug Taps please add an S or P to the catalogue number. Taper Taps will be supplied unless otherwise requested.

13/16inch O.D.