Electronics & Programming

Low cost momentary (non-locking) action panel mounting push to make switches. Supplied with fixing nut & washer 7mm cut out. External Diameter:10mm External Length / Height:28mm

• Perfect way to get started with programming and hardware interaction • No soldering required • All parts are included to build 6 projects • Small prototype breadboard included • Projects: Dice, Buzzer, Theremin, Miniature Steady Hand Game, Fruit Keyboard, Traffic Lights Kit contains: 1 x micro:bit, 1 x piezo buzzer, 1 x 170 pin breadboard, 1 x 10mm red LED, 1 x 10mm yellow LED, 1 x 10mm green LED, 1 x battery case with AAA batteries, 1 x set of crocodile clip wires and 0.5mm micro USB cable

This kit is designed for Workshops to learn about Arduino, Sensors, Actuators, Coding and Design. It includes a full how-to guide online, and comes with the following: YourDuinoRoboRED Arduino-UNO-compatible with built-in 3-pin I/O connectors, higher-current 5.0V and 3.3V supply. 1 x Bluetooth Radio remote interface: connect to Smartphones etc. 5 x Big push-button switches [Digital Input] 2 x 10K Potentiometers that fit breadboard well [Analog Input] 5 x 10K Photo Resistors (Light sensors) [Analog Input] 1 x Ultrasonic Distance Sensor [Digital Signal Input] 1 x Joystick Module {Analog Input] 1 x Digital temperature sensor DS18B20 [Digital Signal Input] 1 x LCD Display 2 lines of 16 characters [Signal Output] 50 x LEDs - 5 assorted colours, plus 10 220 ohm resistors (below) [Digital or Analog Output] 1 x Red-Green-Blue Multicolour LED [Digital or Analog Output] 1 x Buzzer Module (makes sound with voltage applied) [Digital Output] 1 x Beeper Module (Makes different sounds/tones with Arduino TONE Library) [Analog Output] 1 x Servo Motor (Mechanical positioning from digital pulses] [Digital Signal Output] 1 x Small Stepper Motor with driver board [Digital Signal Output] 1 x DC Motor small 5V 1 x Power Transistor NFET (Can control DC motor, other large DC loads) 2 x 3-pin cables to 3-pin connectors that fit the Robo1 and various Electronic Bricks etc. 2 x 3-pin cable to separate wire ends that connect the Robo1 to any device 1 x USB Cable (50cm) 1 x 40 wide flat rainbow color cable that can be separated to make many different cables 2 x 40 pin strips that can be separated to connect cables to breadboard and other devices 10 x 220 ohm resistors (LED current limit etc.) and 10K resistors (switch pullups etc.) 1 x 8cm high-quality Breadboard with power and ground strips

Omega lead-free solder is the ultimate in environmental health management, manufactured in the U.K. from 96% tin, 3.5% silver and 0.5% copper. It is rosin-free, halidefree and has a flux content of 3%. A fast flow solder, with good solderability, minimal clear residue and a melting point of 217°C. 250g reels.

soLID core - Rated: 1.8A @ 1000V RMS max. size 1/0.6mm. 100 metre reel

For all Antex and most other brands of soldering iron. This stand is adjustable for the model of iron used. It is made from high grade phenolic, has slip resistant feet, and a ballast weight for stability.

The model DS has double O ring washers for increased suction. Replaceable nozzle. Lightweight and easy to use.200mm long x 20mm dia.

60/40 Tin/Lead alloys with five cores of non corrosive flux. The 'Savbit' alloy will help prevent corrosion of copper soldering bits.

Spare sponge for ST4 & ST6 soldering iron stands.

Soldering Iron Element CS Iron 240v

The ST6A is an industrially styled bench stand for ANTEX M, C, CS, XS, TCS, TC & SD soldering irons. Ideal for use when a fume extraction tube is used. It is manufactured from high grade materials, suitable for use with soldering iron tip temperatures. It incorporates slip-resistant feet, and a ballast weight for added stability. The innovative design ensures that the soldering iron handle temperature is kept to a minimum when the iron is placed in the stand for long periods.

Supplied fitted with a 3 pin connector for connecting to appropriate service trunking or the Antex power supply (700-190).

60/40 Tin/Lead alloy with low fume, high purity halide free flux core. For use where a minimum of fume and residue are required. 500g reel.

This power supply unit plugs directly in to a standard13A mains socket. Maximum power rating 24W, suitable for use with the 24 volt versions of the Antex C, M, CS or XS irons.

Omega lead-free solder is the ultimate in environmental health management, manufactured in the U.K. from 96% tin, 3.5% silver and 0.5% copper. It is rosin-free, halidefree and has a flux content of 3%. and a melting point of 217 °C. 250g reels.

For general purpose welding and brazing.

Sifbronze No.1 brazing rod for general purpose use. Melting Temp: Between 875 - 895 ºC

• Nominal Power - 18 watts • Supplied with long-life iron plated bit • Antex 1100 bit is fitted to this iron (2.3mm) • An inner ceramic shaft provides near perfect insulation • Burn-proof silicone cable. Ideally suited to educational environments • Supplied complete with 2.3mm bit, 1.5m of cable and full instructions • CE marked Uses 1100 series replacement bits and a range of alternative sized bits are also available. Soldering iron stands are available separately.

Fast flow Hardcore Solder is a flux core contained within a high purity solder wire. It eliminates soldering defects, has no offensive odours and is an assured non-corrosive, no-clean solder. 500g reels.

Soldering Iron Tip for CS Iron 2.3 dia point

• Nominal Power - 25 watts • Supplied with long-life iron plated bit • Antex 50 bit is fitted to this iron (2.3mm) • An inner ceramic shaft provides near perfect insulation • Burn-proof silicone cable. Ideally suited to educational environments • Supplied complete with 2.3mm bit, 1.5m of cable and full instructions • CE marked Uses 50 series replacement bits and a range of alternative sized bits are also available. Soldering iron stands are available separately.

Contain a soldering iron, an ST6 stand and a length of solder. With Silicone Rubber cable, complete with fitted plug. 220/240 volt only.

Soldering Iron Tip for XS Iron 2.3 dia point

Helps to look after your soldering iron tip and can aid cleaning of an oxidised tip

Silver oxide batteries can be used in place of alkaline batteries i.e. LR44 = SR44

This specially designed E-Textiles coin cell holder has large connection points for the conductive thread. It also has an integrated in power switch.

Low cost miniature transistor oscillator buzzers with flying leads. Ideal for educational projects and general purpose use. Frequency: 400Hz Sound Output: 75dB @ 30cm. Current: 30mA Dims: 23L x 17W x 15H Fixing Centres: 27.5mm Lead Length: 100mm

Solid state. Sound output 75dB @ 30cm. Frequency 400Hz. Fixing centres 27.5m.

Current Rating 10A Voltage Rating 250V(ac) Length 3m Colour Black Overview C13 to BS1363 Economy 10A Power cords suitable for office and light use environments. The BS 1363/A 13A fused mains plug has a riveted/welded construction and is non-rewireable. Cable fully tested and approved by ASTA and strain relieved at both ends. Range Overview IEC to BS1363 Plugs A range of electrical appliance connecting leads, the majority of which are terminated with connectors that conform to IEC 60320. The IEC (International Electrotechnical Commission) is the international standards and conformity assessment body. The 'odd' 'C' numbers refer to a socket type connector - mains input - and the 'even' 'C' numbers refer to a plug type connector - the appliance inlet.

Ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered. They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

Miniature low-cost toggle switches.

Economy stripboard for PCB work. Size: 25 x 64mm.

Mains Fuse 13 amp 240 volt

This sewable slide switch allows LEDs to be turned on or off in your E-Textiles project. It has 2 connection points to which the conductive thread is connected.

A red lead with stackable 4mm plug at each end, 500mm long, extra flexible wire. Max current 0.5A continue.

A black lead with stackable 4mm plug at each end, 500mm long, extra flexible wire. Max current 0.5A continue.

Solid state. Sound output 75dB @ 30cm. Frequency 400Hz. Fixing centres 27.5m.

A dragster kit that allows multiple choices for transmission and student development. It promotes a strong collective commitment to making and testing an identical chassis. The kit ensures students can create their own original dragsters. Features: - Belt driven with the option of 3 pulley diameters. - Choice of mounting the rear wheels of 4 different diameters. - Demountable wheel to highlight slip / traction. - Front axle configured in different ways to search for the best straight-line guidance. - Multiple configurations for the body cover, depending on student preference. Requires 3 AA batteries. Dimensions depending on configuration, expanded PVC frame 6 x 40 x 200 mm. Includes a variety of parts including wheels and pulleys of different diameters. Excludes the material for the body, allowing students to develop their own from a chosen material. Available as a single pack or a pack of 10. Batteries not included. This kit enables you to make up to 10 Dragsters.

PP3 size holder. PCB mounting - 2 terminals 0.8 dia. Pin spacing 12.7mm.

10 leads in 5 assorted colours, typically 457mm length, with PVC insulated miniature crocodile clips at each end. Max current 0.5A continuous. Pack of 10

A model/test bench To test and understand basic construction principles • How are buildings and structures built? • What are the characteristics of buildings? • Why don't buildings fall down? The concrete block test bench allows students to work on basic construction principles using stacked blocks.

Bridges Test Stand This kit enables students to compare different types of bridges. Students will assemble and test various systems and observe the characteristics of each bridge struture. Comes boxed as a self assembly kit Dimensions: H 250mm x L 520mm Truck for the Bridge test stand can be purchased. 560-776 Truck (300g)

Dragster kit that works with solar energy. The solar cell is 60 x 60mm. Dimensions: L 150 x W 60 x H 95mm. The kit involves a variety of skills across the curriculum including cutting, drilling, wiring, assembly. Includes all parts and materials required: • Solar cell • Solar motor • Mechanical parts • Chassis and cover pre-cut to dimensions This kit enables you to make ten Solar Dragsters.

Dual Fuel Dragster has a switch to select the source of energy, either battery or solar cell. The lightness of the vehicle and the great sensitivity of solar propulsion engine, works even under hazy sunshine. • Features steerable front wheels • Dimensions: L 210 x W 80 x H 70mm • Weight: 70g This kit enables you to make one Solar Dragster.

Low cost batteries with a shelf life of 2 years, suitable for low drain applications. Sold singly.

Low cost batteries with a shelf life of 2 years, suitable for low drain applications. Pack of 2.

A range of low-cost wirewound controls, ideal for loudspeaker volume controls, miniature motor speed controllers, etc. Rated at 5 watts. Body Diameter: 24mm, Body Depth: 11mm, Spindle Diameter: 6mm, Spindle Length: 6.5mm (17 inc bush)

Lens ended MES bulb 2.2V 250mA.

These batteries have a 7 year shelf life and are suitable for highh drain rate applications. They have a better low temperature performance than Zinc cells. Pack of 2.

250g reel of uninsulated Bare Copper Wire Dia. 1.626mm