Vacuum Formers

The kit contains eight separate moulds and comes complete with MDF baseboard, plastic skin material and a can of spray adhesive to bond them to the cut foam blocks. The moulds included are for a salad server, clock, child's chair, 75mm radius and 125mm radius.

Compact and affordable. C R Clarke 1210 vacuum former is an ideal entry level machine. Its smaller forming area means lower cost for materials. Perfect for first time users and simple model making. 240V, single phase. Key features: • 4 independent ceramic heaters - Balance out temperature variations across four zones • Interlocked guard - Moving parts are safely contained while allowing good visibility of the forming process • Blow release - Remove parts from mould without effort • No-volt safety switch - Automatically isolates machine in the event of power failure Included items: • C R Clarke 1210 vacuum former machine • Starter pack of material

Turn your C R Clarke 1210 vacuum former into a mobile workstation. Sturdy, easy to move, and features a storage shelf to keep all accessories to hand. Ideal for small departments where worktop space is limited.

This machine is a perfect mid-range vacuum former, ideal for schools and model makers. It has a smaller forming area than the C R Clarke 750FLB, and is desktop mountable. 240V, single phase. Key features: • Independent ceramic heaters - Balance out temperature variations across four zones • Interlocked guard - Moving parts are safely contained while allowing good visibility of the forming process • Digital timer with alarm - Monitor the cycle more efficiently • Blow release - Remove parts from mould without effort • No-volt safety switch - Automatically isolates machine in the event of power failure * Reducing frame available - Decrease the forming aperture Included items • C R Clarke 725FBL vacuum former machine • Starter pack of material

Reduces the standard forming area of the C R Clarke 725 and 917 vacuum formers from 228 x 432mm to 228 x 216mm.

Turn your C R Clarke 725 vacuum formers into a mobile workstation. Sturdy, easy to move, and features a storage shelf to keep all accessories to hand. Ideal for small departments where worktop space is limited.

The 320 Dome Blowing Unit consists of a rigid base with a heat-proof seal plate that has perforations to allow air to be injected. A sheet of thermoplastic material, normally cast acrylic, is heated in an oven to its softening temperature. The material is transferred to the Dome Blowing Unit and is clamped into position. Air is blown under the sheet using the control valve on the front panel, inflating the dome. An adjustable height gauge assists the user to achieve consistent dome heights. Once cooled, the dome is unclamped and is immediately ready to use. The 320 requires an external air supply, this can come from a compressed air supply or the Pressure Outlet of one of our Vacuum Forming Machines. The 320 is supplied with rings to make domes of 300, 225 and 150mm in diameter.

A kit of parts for replacing the silicone seals etc on popular vacuum formers. If your machine is not performing well, the filter may also need replacing. Includes silicone seal, platen seal filter element & adhesive

Service kit for replacing silicon seal on the CR Clarke 1210 Vacuum Former. Service kit includes: silicone seal, platen seal, adhesive, and primer. NOTE: If your machine is not performing well, the filter may also need replacing.

A kit of parts for replacing the silicone seals etc on popular vacuum formers. If your machine is not performing well, the filter may also need replacing.

• Vacuum flow rate - 8m3 per hour • Vacuum level - 85% - 8.5 tonnes per m2 • No of ports/format - one port, desk top plywood frame • Standard bag size - one bag @ 1300mm x 2500mm • Maximum bag size - two bags @ 1300mm x 3000mm This comes with a bag kit whic consists of: 1 x 1300mm x 2500mm, 300micron polyurethane bag 2 x sets of plastic closure strips (to hold bag closed at each end) 1 x plastic round bag connector 1 x 8mm push-fit adaptor (which screws into the bag connector) Note: There is a small bag of fittings placed in the top of the tube containing the bag.

Reduces the standard forming area of the C R Clarke 750 vacuum former from 482 x 432mm to 228 x 216mm.