TSL

• Nominal Power - 18 watts • Supplied with long-life iron plated bit • Antex 1100 bit is fitted to this iron (2.3mm) • An inner ceramic shaft provides near perfect insulation • Burn-proof silicone cable. Ideally suited to educational environments • Supplied complete with 2.3mm bit, 1.5m of cable and full instructions • CE marked Uses 1100 series replacement bits and a range of alternative sized bits are also available. Soldering iron stands are available separately.

Sifbronze No.1 brazing rod for general purpose use. Melting Temp: Between 875 - 895 ºC

Best quality. Sheet size 280 x 230mm. Grade: S2 coarse (40 grit). Note: Colour may vary.

For general purpose welding and brazing.

• Nominal Power - 25 watts • Supplied with long-life iron plated bit • Antex 50 bit is fitted to this iron (2.3mm) • An inner ceramic shaft provides near perfect insulation • Burn-proof silicone cable. Ideally suited to educational environments • Supplied complete with 2.3mm bit, 1.5m of cable and full instructions • CE marked Uses 50 series replacement bits and a range of alternative sized bits are also available. Soldering iron stands are available separately.

Fast flow Hardcore Solder is a flux core contained within a high purity solder wire. It eliminates soldering defects, has no offensive odours and is an assured non-corrosive, no-clean solder. 500g reels.

• Packs of 25 sheets • Silicone carbide paper sheets. Latex quality • Sheet size 280 x 230mm

• Packs of 25 sheets • Silicone carbide paper sheets. Latex quality • Sheet size 280 x 230mm

Best quality. Sheet size 280 x 230mm. Grade: F2 100 grit. Note: Colour may vary.

Soldering Iron Tip for CS Iron 2.3 dia point

Contain a soldering iron, an ST6 stand and a length of solder. With Silicone Rubber cable, complete with fitted plug. 220/240 volt only.

This specially designed E-Textiles coin cell holder has large connection points for the conductive thread. It also has an integrated in power switch.

Helps to look after your soldering iron tip and can aid cleaning of an oxidised tip

Silver oxide batteries can be used in place of alkaline batteries i.e. LR44 = SR44

Best quality. Sheet size 280 x 230mm. Grade oo very fine (240 grit). Note: Colour may vary

Best quality. Sheet size 280 x 230mm. Grade: O fine (220 grit). Note: Colour may vary.

Soldering Iron Tip for XS Iron 2.3 dia point

Current Rating 10A Voltage Rating 250V(ac) Length 3m Colour Black Overview C13 to BS1363 Economy 10A Power cords suitable for office and light use environments. The BS 1363/A 13A fused mains plug has a riveted/welded construction and is non-rewireable. Cable fully tested and approved by ASTA and strain relieved at both ends. Range Overview IEC to BS1363 Plugs A range of electrical appliance connecting leads, the majority of which are terminated with connectors that conform to IEC 60320. The IEC (International Electrotechnical Commission) is the international standards and conformity assessment body. The 'odd' 'C' numbers refer to a socket type connector - mains input - and the 'even' 'C' numbers refer to a plug type connector - the appliance inlet.

Low cost miniature transistor oscillator buzzers with flying leads. Ideal for educational projects and general purpose use. Frequency: 400Hz Sound Output: 75dB @ 30cm. Current: 30mA Dims: 23L x 17W x 15H Fixing Centres: 27.5mm Lead Length: 100mm

Ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered. They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

Solid state. Sound output 75dB @ 30cm. Frequency 400Hz. Fixing centres 27.5m.

Miniature low-cost toggle switches.

Economy stripboard for PCB work. Size: 25 x 64mm.

Mains Fuse 13 amp 240 volt

A dragster kit that allows multiple choices for transmission and student development. It promotes a strong collective commitment to making and testing an identical chassis. The kit ensures students can create their own original dragsters. Features: - Belt driven with the option of 3 pulley diameters. - Choice of mounting the rear wheels of 4 different diameters. - Demountable wheel to highlight slip / traction. - Front axle configured in different ways to search for the best straight-line guidance. - Multiple configurations for the body cover, depending on student preference. Requires 3 AA batteries. Dimensions depending on configuration, expanded PVC frame 6 x 40 x 200 mm. Includes a variety of parts including wheels and pulleys of different diameters. Excludes the material for the body, allowing students to develop their own from a chosen material. Available as a single pack or a pack of 10. Batteries not included. This kit enables you to make up to 10 Dragsters.

A model/test bench To test and understand basic construction principles • How are buildings and structures built? • What are the characteristics of buildings? • Why don't buildings fall down? The concrete block test bench allows students to work on basic construction principles using stacked blocks.

10 leads in 5 assorted colours, typically 457mm length, with PVC insulated miniature crocodile clips at each end. Max current 0.5A continuous. Pack of 10

This sewable slide switch allows LEDs to be turned on or off in your E-Textiles project. It has 2 connection points to which the conductive thread is connected.

A black lead with stackable 4mm plug at each end, 500mm long, extra flexible wire. Max current 0.5A continue.

A red lead with stackable 4mm plug at each end, 500mm long, extra flexible wire. Max current 0.5A continue.

Solid state. Sound output 75dB @ 30cm. Frequency 400Hz. Fixing centres 27.5m.

PP3 size holder. PCB mounting - 2 terminals 0.8 dia. Pin spacing 12.7mm.

Dragster kit that works with solar energy. The solar cell is 60 x 60mm. Dimensions: L 150 x W 60 x H 95mm. The kit involves a variety of skills across the curriculum including cutting, drilling, wiring, assembly. Includes all parts and materials required: • Solar cell • Solar motor • Mechanical parts • Chassis and cover pre-cut to dimensions This kit enables you to make ten Solar Dragsters.

Dual Fuel Dragster has a switch to select the source of energy, either battery or solar cell. The lightness of the vehicle and the great sensitivity of solar propulsion engine, works even under hazy sunshine. • Features steerable front wheels • Dimensions: L 210 x W 80 x H 70mm • Weight: 70g This kit enables you to make one Solar Dragster.

Bridges Test Stand This kit enables students to compare different types of bridges. Students will assemble and test various systems and observe the characteristics of each bridge struture. Comes boxed as a self assembly kit Dimensions: H 250mm x L 520mm Truck for the Bridge test stand can be purchased. 560-776 Truck (300g)

A range of low-cost wirewound controls, ideal for loudspeaker volume controls, miniature motor speed controllers, etc. Rated at 5 watts. Body Diameter: 24mm, Body Depth: 11mm, Spindle Diameter: 6mm, Spindle Length: 6.5mm (17 inc bush)

250g reel of uninsulated Bare Copper Wire Dia. 1.626mm

These batteries have a 7 year shelf life and are suitable for highh drain rate applications. They have a better low temperature performance than Zinc cells. Pack of 2.

Low cost batteries with a shelf life of 2 years, suitable for low drain applications. Pack of 2.

Low cost batteries with a shelf life of 2 years, suitable for low drain applications. Sold singly.

Lens ended MES bulb 2.2V 250mA.

Presented in a Gratnells tray for easy storage, this Gluestick pack is excellent value. With this pack, you will receive 72 premium, non-toxic, acid and solvent-free gluesticks perfect for use by children in the classroom. What's better, with an ultra-high standard PVP formula, these gluesticks have a shelf-life three times longer than a standard PVA gluestick, so you don't have to worry about them drying out! • Premium retractable medium gluesticks presented in a handy Gratnells classtray • Made from an ultra high-quality PVP formula • Gluesticks are non-toxic, acid-free, solvent-free and completely washable • Ideal for sticking paper, card or photos, and for use in arts and crafts • PVP formula allows for an approximately 3 times longer shelf-life than a standard PVA gluestick!

White Hook and Loop tape 20mm wide x 10 metres. One strip of self adhesive hook type tape and one strip of loop type tape which attach to each other.

• Packs of 25 sheets • Silicone carbide paper sheets. Latex quality • Sheet size 280 x 230mm

Red PVC adhesive tape, electrical grade conforming to BS 3924. In 19mm wide rolls.

These batteries have a 7 year shelf life and are suitable for high drain rate applications. They have a better low temperature performance than Zinc cells. Pack of 2

These batteries have a 7 year shelf life and are suitable for high drain rate applications. They have a better low temperature performance than Zinc cells. Sold singly.

These Bostik Glue Sticks can be used with the Craft Glue Gun and will bond most household materials instantly with a clean, economical and strong bond, making them ideal for household repairs, craft and hobby use. Sticks PVC, metal, fabric, leather, tiles, brick and much more Adhesive is colourless and odourless. Stick diameter 11mm Length of each stick is 190mm Supplied in 5kg pack.

Coloured general purpose adhesive, 200mm in length, 12mm dia. This length of stick can easily be cut with snips or knife to the length required. Sold in packs of 10 assorted colours. For high temperature glue guns.

Aliphatic resin glue provides a strong initial tack and fast speed of set to reduce clamp time. Develops a bond stronger than the wood itself. Excellent sandability and unaffected by finishes.

All-purpose clear oval low temperature glue sticks that only fit the Princess low temperature glue gun. Type: Low temperature Length: 100mm Pack size: 1250 Weight: 10kg

The dispenser prevents spills, fumes and contamination. Light pressure of a brush on the dispensing dish instantly pumps the desired amount of solvent. Made from stainless steel and polythene.

Black PVC adhesive tape, electrical grade conforming to BS 3924. In 19mm wide rolls.

Steel Metric Rolled Thread Zinc Plated.

Steel Metric Rolled Thread Zinc Plated.

Steel Metric Rolled Thread Zinc Plated.

Steel Nuts zinc plated pack of 100

Steel Nuts zinc plated pack of 100

100 1x1/8 Round Head Alloy Rivets

100 1/8 Medium Grip Aluminium Pop Rivets

Pack of 100 M4 diameter wing nuts.

These metal cutting discs have been developed to make angle grinders more versatile in use, these wheels must never be used for grinding. Presented to the workpiece at an angle of 90 degrees typical applications include cutting of keyways, and general cutting of metal. Size. 115 mm x 3.2 x 22 mm.

12inch Diameter for D530-300 & other 12inch disc sanders.

12inch Diameter for D530-300 & other 12inch disc sanders.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

• Quality reprocessed grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

Robust cast-iron frame with steel threaded bar. Tommy bar handle for easy tightening. Swivel shoe allows for clamping irregular-shaped objects. Copper-plated thread prevents weld spatter from sticking. Reinforced shoulders provide greater strength. Corrosion-resistant frame finish.* *QGT - Quality Guaranteed Tools. Tools from a variety of sources which offer exceptional value for money.

Made from U section, extruded aluminium with cast head and foot. Spring-loaded rapid adjustment mechanism sets foot to correct position on bar. Deep-cut Acme thread enables final tightening and application of clamping pressure.

Wood chisel with a fully ground forged steel blade. Fitted with a polypropylene handle in carver style for comfort and durability. Shock absorbing washer between handle and blade. Comes with blade guard for safety. Set of 4 chisels 6mm, 12mm, 18mm, & 25mm. Type. Bevel Edge.

Bastard Cut 250mm

Smooth Cut 250mm

Bastard Cut 200mm

Second Cut 200mm

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 3mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 10mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 3mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 6mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 3mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 3mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 3mm This material is Not suitable for use on a laser cutter.

PVC foam sheet can be sawn, drilled, milled, painted, printed, welded, thermo formed (especially line bent), screwed, riveted and glued with both solvent and contact adhesives. It is ideal for CNC machining. Please note, sheet sizes are nominal. Sheet size 1220 x 610 x 3mm This material is Not suitable for use on a laser cutter.

Score before bending to produce a plastic hinge that can be folded millions of times. It is virtually impossible to tear, resistant to water, oil, most chemicals and high temperatures. Translucent finish.

The resins used in bonding Medite Exterior MDF contain no formaldehyde. This results in very low emission rates due only to the natural wood itself. Suitable for use on a laser cutter. You may need to tape the sheet down for acurate cutting. Pack 0f 6 600 x 400 x 6mm sheets. PLEASE NOTE: While every effort is made to ensure that all sheets are completely flat, due to the manufactured size and thickness, some sheets may be slightly bowed. To reduce the risk of warping, MDF sheet should be stored flat in a dry, well ventilated area as it is susceptible to moisture absorpttion.

""A virtually unbreakable blade ideal for all material types, including sheet metals and hard steels. These blades are particularly useful when working in restricted access areas due to their thinness and flexibility, or on site where the workpiece cannot easily be secured

Quality heat treated steel with accurately set and shaped teeth. Supplied in standard 165mm size to fit most coping saws. 24TPI and pinned ends. Pack of 10

Quality heat treated steel with accurately set and shaped teeth. Supplied in standard 165mm size to fit most coping saws. 14TPI and pinned ends. Pack of 10.

Stanley 018 Interlock snap-off 18mm blade. These knives provide safer operation because the blade is clamped firmly in place. It can be locked in the extended or retracted positions. They accept standard craft knife blades.

QGT hammers have drop forged, hardened tool steel heads and lacquered ash handles. They comply with BS876.

For delicate, precision cutting, trimming and stripping. Shaft 120mm x 8mm dia.

Stanley Throwaway Knife Pack of 50

Stanley Knife Blades 1991 Pack of 5

Second Cut 250mm

Smooth Cut 200mm

Quick change bar clamp with a revolutionary design. A trigger releases the pressure instantly and a quickchange jaw converts the clamp to a spreader in seconds. Three sizes are available. 60mm Bite Depth