Gas Prep & Analysis

Pair of rods.

Carbon rods, 100 x 5 mm. Pack of 10 rods.

Carbon rods, 200 x 8 mm. Pair of rods.

Platinum electrodes, with screw terminals. Manufactured in borosilicate glass. Length from tip of foil to tip of terminal, 114 mm.

These versatile electrode holders are suitable for holding Carbon rod electrodes as well as metal strip electrodes. They are designed to fit over 100 mL and 250 mL glass beakers, being held in place by small plastic lugs to prevent them slipping off. Resistant to corrosion, they accept 6 - 8 mm diameter cylindrical (e.g. carbon) electrodes and 19mm wide, 0.8 mm (minimum) thick metal strip electrodes. The brass connectors also resist corrosion and are compatible with the usual 4 mm stackable type lab leads. To tighten the carbon electrodes without crushing them, the setscrew is equipped with stop. • 4 mm sockets • Dimensions (L x W x H): 100 x 40 x 15 mm • Complete with 2 carbon electrodes

These 'S' shaped electrodes are convenient and easy to use simply hang them over the rim of the beaker containing the electrolyte and connect crocodile clips with 4 mm leads to them! Made from insulated brass, with a short length of carbon rod attached at the lower end and bare contact at the top for attaching crocodile clip. Supplied as a pair of electrodes.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

These round electrodes will fit the electrode holder EL110620, the electrode connector EL150426, and rubber stoppers with hole. Diameter 6-7 mm.

Dimensions: 100 x 10 mm. Sold in packs of 10.

Each cell consists of 75 x 25 mm glass cylinder with 2 hole rubber stopper fitted with carbon electrodes. Electrical contact is made through the crocodile clips and a piece of insulating material between the electrodes prevents short circuiting. The gases evolved are collected in two 75 x 10 mm test tubes suspended over the electrodes by piece of wood and rubber bands (not supplied).

Spare glass tube for EL06891.

Spare carbon electrodes for EL06891.

This kit uses the juice within lemon as an electrolyte in an oxidation-reduction reaction to produce useful electricity sufficient to power clock. The electrodes must be sanded clean between each attempt. Requires lemons to make ""batteries"" in series to generate sufficient voltage to power the clock.

Consisting of an inverted U-tube with its ends closed by sintered discs. Dimensions (Diameter W x H): Arms 13 x 80 x 100 mm.

This set allows students to experiment with the characteristics of primary cells (voltaic cells). By using different electrodes and electrolytes, various voltaic cells can be made and tested. The set contains various different electrodes, including zinc, lead, aluminium, carbon, tin, copper, nickel and iron. Also included are a plastic cell container with electrode holders and porous pot. Instructions included. Dimensions: 100 x 20 mm (approx.).

Suitable for use with EL180875 and EL180877.

Comprises three parallel tubes, joined at the bottom with a horizontal tube. The central tube has a funnel for filling with water, and the side tubes have open ends at the bottom to allow bungs that hold electrodes to be fitted, and jets with stopcocks at the top for collecting gas in test tubes. The side tubes are graduated 0-50 x 0.2 mL so that the volume of gas in each can be measured. Clamps and support base (sold separately) are recommended so the unit can be mounted on retort rod.

Comprises three parallel tubes, joined at the bottom with a horizontal tube. The central tube has a funnel for filling with water, and the side tubes have open ends at the bottom to allow bungs that hold electrodes to be fitted, and jets with stopcocks at the top for collecting gas in test tubes. The side tubes are graduated 0-50 x 0.2 mL so that the volume of gas in each can be measured. Clamps and support base (sold separately) are recommended so the unit can be mounted on retort rod.

For student experiments. Embedded platinum electrodes are connected via 4 mm sockets. Two miniature test tubes are included for gas collection.

Earthenware.

Earthenware.

Glass with base and ground top flange.

Glass with base and ground top flange.

Glass with base and ground top flange.

Glass with base and ground top flange.

Glass with base and ground top flange.

Ground one side. Supplied in packs of 5.

Ground one side. Supplied in packs of 5.

Graduated 50 x 0.1ml. Closed at one end.

Circular pneumatic trough, made from clear soda-lime glass.

Circular pneumatic trough, made from clear soda-lime glass.

Circular pneumatic trough, made from clear soda-lime glass.

The head is fitted with 8 mm diameter inlet and outlet tubes.

Holder for glass gas syringes.

Ground glass syringe. Marked with 20 mL major graduations, and 1 mL minor graduations. Suba-Seal Stoppers ST14710 or ST14715 can be used as resealable stoppers. For video demonstration, visit timstar.co/SubaSealSyringe

Luer fitting, interchangeable pistons and barrels.

Luer fitting, interchangeable pistons and barrels.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Eight types available. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. ** please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Eight types available. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. ** please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Eight types available. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. ** please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. please note these are not suitable for use at higher temperatures as this will distort the polypropylene.

Pre-bent rigid polypropylene delivery tubes. Unbreakable in normal use ideal substitutes for fragile glass alternatives. Suitable for many types of gas collection experiments. Supplied in pack of 5. The tubes have an i.d. of 4 mm, and an o.d. of 6 mm. please note these are not suitable for use at higher temperatures as this will distort the polypropylene.