TSL - Technology

Wood lathe extraction kit containing everything required to connect a wood lathe to our extraction system including scoop hood, frame assembly, ducting and fixings.

This blade can be supplied in lengths between 3656mm - 3962mm (12-13ft) and 6, 10, 14 or 24 TPI. PLEASE SPECIFY YOUR REQUIRED LENGTH (in mm) AND TPI WHEN ORDERING. Because they are made to order they can take up to 2 weeks to supply.

This blade can be supplied in lengths between 3656mm - 3962mm (12-13ft) and 6, 10, 14 or 24 TPI. PLEASE SPECIFY YOUR REQUIRED LENGTH (in mm) AND TPI WHEN ORDERING. Because they are made to order they can take up to 2 weeks to supply.

• Fully hardened high carbon steel bit • Precision ground tri-point bit for a clean cut and reduced splintering • Sizes: 10, 16, 20, 22, 25 and 32mm bits • For drilling softwood, medium hardwood, particle board, plasterboard, plastics and fibreglass • For use with drills, drivers and hand braces Pack of 6.

Suitable for use in chip forges and chip brazing hearths. 12.5kg

• Machine Type - Medium /Bench or Pedestal • Method of attachment - Secures around depth stop collar using fixing top to suit configuration • Positive Manual latch • Flip up with spring retention • Construction - Aluminium/Nylon with Polycarbonate Vizor which encloses the work area • Operation - Telescopes on contact with work piece, length adjustable vizor Please state collar size when ordering. Maximum chuck dia. for the MT is 63mm / MTS is 70mm.

• Machine Type - Light/Bench or Pedestal • Method of attachment - secures to drilling machine spindle collar • Positive manual latch • Flip up with spring retention • Construction - moulded polycarbonate • Operation - Telescopes on contact with work piece, length adjustable vizor which encloses the work area Collar size: 62.5mm

Meddings drill guard to fit Meddings Driltru: L1 L2 M2 M4 & MV4. Clamp diameter for Drill guard 64mm.

• Machine Type - Medium /Bench or Pedestal • Method of attachment - Secures around depth stop collar using fixing top to suit configuration • Positive Manual latch • Flip up with spring retention • Construction - Aluminium/Nylon with Polycarbonate Vizor which encloses the work area • Operation - Telescopes on contact with work piece, length adjustable vizor Please state collar size when ordering. Maximum chuck dia. for the MT is 63mm / MTS is 70mm.

M2 Min-Max Vertical height: 250-450mm Overall length - enclosed: 475-800mm Overall length - extended: 925-1250mm Please note: We require T-slot size to match this product to your machine.

Spare vizor for BT Drill guard (590-204 & 590-204X). Constructed from scratch resistant polycarbonate.

• Machine Type - Light/Bench or Pedestal • Method of attachment - secures to drilling machine spindle collar • Positive manual latch • Flip up with spring retention • Construction - moulded polycarbonate • Operation - Telescopes on contact with work piece, length adjustable vizor which encloses the work area The maximum collar size for the BT is 70mm (minimum 40mm). Please state collar size when ordering.

• Machine Type - Light/Bench or Pedestal • Method of attachment - secures to drilling machine spindle collar • Positive manual latch • Flip up with spring retention • Construction - moulded polycarbonate • Operation - Telescopes on contact with work piece, length adjustable vizor which encloses the work area Collar size: 64mm

A range of accessories for use with any extractor. Jubilee clips are Kite marked to BS5315 (1991) and the company is licensed to BS EN ISO 9001. Made from mild steel, zinc protected and used for fixing flexible rubber hoses, metal tubes etc. BZP Size 5 Adjustment . 90 - 120mm Adjustment. 3.1/2 - 4.3/4in

A cartridge filter for the Woodvac TS100.

Filter bags for WV150 Pack of 6

Pack of 5 standard poly waste bags. Size 915mm x 812mm (36"" x 32"").

Used for Hegner Multicut scrollsaw and extraction installations to connect a Multicut to a dust extraction system for optimum dust removal.

Contents: LH Turning Tool 12mm Shank RH Turning Tool 12mm Shank Pack of 10 Inserts for LH/RH Turning Tools Parting Off Tool 12mm Shank with 10 Inserts External Threading Tool 12mm Shank with 10 Inserts Boring Bar 8mm Shank with 10 Inserts 5mm Centre Drill 2 Stub Drills (5mm & 10mm) 4 Turret Bushes (2 x 5mm, 8mm & 10mm)

These switches can be mounted conveniently as foot / knee / palm switches and wired into the machine by a competent electrician. • Ingress protection to Ip67 • 1 N/O, 1 N/C contacts (10A) • 5 x PG13 cable entries (1 threaded) • IEC418 tamperproof, UL and CSA approved Dimensions: 94mm x 94mm

Programmable spindle speeds and feedrates make the Turn 270 Pro ideal for cutting a range of resistant materials such as wax, plastic, acrylic, free cutting alloys, aluminum and steel. THE TURN 270 PRO COMES AS STANDARD WITH: • VR CNC Turning Operating Software (PC not included) • QuickTURN 2D Design Software (1 seat) • Quick Change Toolpost and Holder • Manual Self Centring 100mm 3 Jaw Chuck • Installation and Instruction Manuals • USB Connection

• Machine Type - Light /Bench or Pedestal (dedicated to machine make) • Method of attachment - Clips to back pillar • Positive Manual latch or interlock • Side opening • Construction - Mild steel with 4 mm polycarbonate vizor • Operation - Remains stationary allowing depth stop collar and chuck to pass through length adjustable vizor

These holesaws cut perfect holes in a wide variety of materials including wood, chipboard, plywood, non laminated plastics, plasterboard and non ferrous metals. Suitable for use in most variable speed power drills. Supplied in a sturdy case for safe and secure storage. Contains: 12 x Varipitch Holesaws: 16, 20, 22, 25, 32, 35, 38, 44, 51, 64, 70, and 76mm. 1 x 3/8in Arbor (14-30mm). 1 x 7/16in Arbor (32-152mm). 1 x Arbor Adaptor. 1 x 300mm Extension Bar. 1 x Aluminium Case.

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 12mm (6tpi) 6tpi - skip teeth & are best for cutting timber

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 12mm (14tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 6mm (14tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 9.5mm (14tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

• Machine Type - Light/ Bench or Pedestal • Method of attachment - Side fixing or clips to back pillar • Positive Manual latch or interlocked • Side opening • Construction - Moulded 5mm polycarbonate body, with 4 mm polycarbonate vizor, adjustable to suit machine depth stop bracket • Operation - Remains stationary allowing depth stop collar and chuck to pass through length adjustable vizor

• Machine Type - Light to medium centre lathes • Method of attachment - Secures to face or top of lathe headstock • Manually adjusted to cover work area. Interlocked • Construction L6 - Cast aluminium and 4 mm polycarbonate visors • Construction L12 & L18 - Mild steel, P.V.C. skirt, 6.6 nylon pivot bushes and 4mm polycarbonate visors • Operation - Hinges to allow access to chuck and work area

315mm Dia, 30mm bore. For accurate sizing and trimming timber and manmade boards. Supplied with standard pinholes including Sedgwick and Scheppach.

315mm Dia, 30mm bore, 14mm pinhole. General purpose giving superior finish for both ripping and crosscutting applications. Supplied with standard pinholes including Sedgwick and Scheppach.

The integral dust extraction model features a Terylene-needlefelt dustbag, filter indicator light, tray collector and comes with an emergency stop bar and fully complies with UK COSHH Regulations, the European Machinery Directive and also with the BS4163 “Health & Safety in Workshop of Schools and Similar Establishments” Regulations. KEY FEATURES • Mounted double end polishers and dust extraction • Supplied with heavy duty adjustable polycarbonate eyeshields • No-volt overload pushbutton controls • Large adjustable mop guards with safe edging • Supplied with one loose leaf and one stitched calico mop • UK manufactured

The TSCS alleviates the need for a Run-Off table behind the saw (a legal requirement) and maximises the floor space. The Extractor is simple to install and a range of Circular Saw Extraction Kits are available for installation by Technology Supplies engineers. Please specify saw model number at time of order placement if this service is required. These products require specialist installation & training. Please contact us for further information.

The TSUB may also be used for other similar applications including portable benches and small individual machines. The TSUB has exceptionally low noise characteristics for use within the classroom and is designed for use with fi ne dusts. Warm air is returned to the classroom being sympathetic to environmental issues. A complete installation service is available by our engineers. Inlet sizes: 1 x 80mm & 1 x 63mm diameter ports, one either side OR 2 x 63mm diameter ports, one either side. Please specify inlet port diameters and locations (LHS/RHS) at time of order placement. These products require specialist installation & training. Please contact us for further information.

The TSFL has exceptionally low noise characteristics for use within the classroom and is designed for use with fine dusts. Warm air is returned to the classroom being sympathetic to environmental issues. The Top Extraction Kit is available for installation by our engineers. Inlet sizes (left and/or right side: 1 x 100mm & 1 x 80mm diameter ports OR 2 x 80mm diameter ports OR 1 x 120mm port on one side only. Please specify inlet port diameters and saw model number at time of order placement. These products require specialist installation & training. Please contact us for further information. Airflow: Approx. 600m3/hr at 1000 pascals.

This disc will not cut fingers even if touched accidentally. With the Tungsten Carbide Flange Cutter (an optional extra) it will cut out the moulding with a 5mm flange around its perimeter. The cutting edge of this cutter is well protected from contact with the user and full instructions are supplied. No volt release switch fitted as standard. Key Features • 400 x 455mm table top • Multi tool arbor • Tungsten carbide abrasive disc and holder • Tool height adjustment facility • Upgradeable to the 2020

The standard tilting table is 226 x 278mm and indexed 135-90°. The bench machine has dust extraction takeoff points and requires a non-latching footswitch (530-795). KEY FEATURES • Bench mounted • Quick action calibrated tilting table for operating positions between 90° and 135° • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 15mm x 1090mm aluminium oxide abrasive belt

It has a large cast iron tilting fence for accuracy and timber support, front and rear cutterblock guards, shaw guards for rebating and features an enclosed drive mechanism. A no-volt release starter with thermal overload, key switch, footswitch and anti-kick back fingers for thicknesser are fitted as standard. KEY FEATURES • Two Knife Cutter block • Cast Iron table • Cast Iron fence • 180 x 255mm thicknessing capacity • 255mm surfacing width • Footstop and key switch included • UK Manufactured

The two fences can be used together with the Tungsten Carbide Disc to cut out slots and rebates in wood. Full instructions are supplied. No volt safety switch fitted as standard. Key Features: • 400 x 455mm table top • Multi tool arbor • Tool height adjustment facility • Adjustable 0 to 10 tilting table • Adjustable guide and extraction fences • Large dia. Hand wheel for tool height adjustment • Full toolkit including tungsten carbide abrasive disc, flange cutter, mini mops & compound bars and mini flapwheels

The bench mounted machines incorporate adjustable dust collection hoppers for use with a centralised dust extraction system. Set of polishing mops included.

The standard tilting table is 226 x 278mm and indexed 135-90°. The bench machine has dust extraction takeoff points and requires a non-latching footswitch (530-795). KEY FEATURES • Bench mounted • Quick action calibrated tilting table for operating positions between 90° and 135° • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 15mm x 1090mm aluminium oxide abrasive belt

The standard tilting table is 226 x 278mm and indexed 135-90°. The integral dust extraction system significantly improves performance and combined with cassette collection and disposal enhances easy, convenient waste handling. Fully compliant with UK COSHH regulations, the European Machinery Directive and also with the BS4163:2014 Health and Safety in Workshops of Schools and Similar Establishments” Regulations. Supplied and fitted with a medium grade, grit belt. KEY FEATURES • Dust extraction mounted • Quick action calibrated tilting table for operating positions between 90 and 135 degrees • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 150 x 1090mm aluminium oxide abrasive belt

250mm dia blade for MACC-TE250.

With a cast iron table at the heart of this compact machine it is designed to offer those with limited space or budgets a real bandsaw with sensible capacity and performance, as an alternative to lightweight hobby machines. It shares the same essential build qualities as its larger cousins, strong steel frames, dynamically balanced bandwheels, cast iron tables and an induction motor. It has been designed to offer the user with space restrictions a serious machine in compact form. Key Features: • Blade Guides - Simple to set and easily adjustable • Sealed for life bearings - Require no maintenance during the life of your machine • Capacity - Large 120 mm depth of cut and 240 mm throat depth make this a compact machine capable of serious work • Strong Fence - With cam action lock for ease of use and simple tension adjustment for clamping strength (clamps at rear of table) • Table - A solid, finely ground cast iron table provides an ideal and low friction work support • Trunnion - Table tilts from 0 - 45º on a solid trunnion with easy to read scale Specification: Maximum Depth of Cut: 120mm Throat Depth: 240mm Table Size: 315 x 350 mm Table Height from Floor: 370 mm Motor Power: 1/2 hp Blade Length: 70 1/2"" Blade Width Capacity: 1/4 - 1/2"" Blade Speed: 740 M / minute Extraction Port Diameter: 58 mm (100 mm with supplied adaptor) Height: 860mm Width: 550mm Depth: 480mm Weight: 30kg

Features: • Movable Head 45° right & left • Reduction unit in oil bath • Membrane pump for coolant • Coolant filter • Vice complete with anti-burr device • Bar stop • 24 Volts low voltage installation with hold-to-run head control knob • Service tools • Instruction manual & spare parts

Pedestal for MACC-TE250

Image shows dust extraction unit incorporated into machine bench.

Programmable spindle speeds and feedrates make the VMC 1300 ideal for cutting a range of resistant materials such as wax, plastic, acrylic, free cutting alloys, aluminium and steel. Also available for integration into FMS/CIM systems (additional equipment must be fitted at the time of manufacture. The VMC 1300 comes as standard with: • VR CNC Milling Operating Software (PC not included) • Installation and instruction manuals • Power Drawbar with manual actuation • Workholding clamps • USB connection

The machine can be supplied for left or right handed operation and for a small surcharge it can be supplied with the necessary parts for easy conversion in the workshop. TECHNICAL DATA • Drilling capacity in mild steel 13mm • Motor 0.25kW Single phase • Throat depth 194mm • Speed range 500-4000rpm • No. of speeds 5 • Table size 235 x 409mm • Dimensions 815 x 372 x 627mm • Weight 46Kg KEY FEATURES • Made in the UK • Bench mounted • Easy to use • Front mounted controls • Head raising mechanism

The machine can be supplied for left or right handed operation and for a small surcharge it can be supplied with the necessary parts for easy conversion in the workshop. TECHNICAL DATA • Drilling capacity in mild steel 13mm • Motor 0.25kW Single phase • Throat depth 194mm • Speed range 500-4000rpm • No. of speeds 5 • Table size 235 x 409mm • Dimensions 815 x 372 x 627mm KEY FEATURES • Made in the UK • Bench mounted • Easy to use • Front mounted controls • Head raising mechanism • Latching footswitch