TSL

Hardpoint saws have a moulded plastic handle and ground teeth. They retain a keen cutting edge even when cutting man made boards.

Diecast handle and oval tubular frame. Wing nut tensioning device for 10-12inch blades. S & J 20T.

Junior Steel epoxy coated frame supplied with an Eclipse metal cutting blade. Throat depth: 67 mm Blade material: Bi-metal Overall length: 260 mm Saw tooth size: 32tpi For use with: Wood, metal and plastic

Lacquered wooden handle, 4½inch throat.

Lacquered wooden handle, 4½inch throat.

Hegner sanding discs with hook and loop on the rear for easy fitting.

Buff coloured packing tape ideal for paper and card. 48mm x 66mm.

Sanding disc for Hegner sander. Size 300mm. 60grit.

Rigid and robust, the body and sliding jaw are cast from close grained grey iron which is machined on all friction surfaces for a smooth, reliable action. Fitted with hardened steel jaws for extended life, they can be replaced when worn. The main steel screw has a two-start rolled thread for faster and smoother operation. It has a fused steel handle that will bend before the vice can be overstressed. A safety stop prevents the slide from being separated from the body. The most popular and widely used general purpose vice for light to medium-duty applications.

British made from high quality cast iron. They have hardened steel replaceable jaw plates.

PVC carrier tape specifically used for bonding plastics to plastics and is ideal for holding material to CNC machine beds etc.

40mm butterfly hinge.

General purpose double sided tape with polyester carrier. Suitable for bonding metal to metal and plastics to metal. 50m long.

Clear adhesive tape 25mm wide x 66 metres.

Electroplated brass Piano hinge 1inch open and 3 feet in length.

A range of light narrow steel butt hinges. Sold in pairs.

• Three accurately ground mounting surfaces for drilling holes at 90° • Made from cast iron • Precision ground jaws • Jaw width: 100mm • Jaw opening: 85mm

Cast iron frame with hardened steel jaw plates and swivel base. Grey iron casting resists distortion under high pressure. Chrome-plated handle and lead screw. Clamp travel - 125mm (8kg vice) and 140mm (16kg vice).

The built-in clamp allows it to be easily and quickly attached to a bench, table or work surface up to 1.5/8in deep. Pipe grips are incorporated below the parallel jaws. A useful anvil is included on the rear of the body. Jaw Width. 75mm (3in).

• Quality cast iron body with curved jaws. • 40mm capacity bench clamping screw

Please specify the choice of frame colour when ordering. • Moisture resistant MDF top with solid beech lippings • Cabinet, 330mm wide x 430mm deep x 510mm high. Made from genuine birch multiply, with solid back panel available in red, blue, green or yellow. • 4 removable trays, available in a range of colours • Optional multi functional anti vibration/locking castors • Maximum of 4 woodwork/metalwork vice fitted (vice details 75mm) •Optional multi functional anti vibration/locking castors

Special fibre more durable than lead or copper. Supplied in pairs. Size. 100mm (4 in).

Portable vices with built-in clamp allows quick and easy attachment to a bench, table or work surface. Woodwork vices, 150mm jaw, 120mm opening. Max table thickness 55mm.

The plain screw works through a separate unbreakable nut securely housed beneath the body seating to ensure constant alignment of screw mechanism. Fitted with front dog. Jaw Width. 175mm (7in). Jaw opening: 200mm (8in)

Fixing kit for 9inch vices.

Record Irwin V175B Woodcraft Vice is designed for the user who requires a more robust vice which is permanently fixed. The main screw has a rolled 2-start acme thread which ensures a smooth strong action with the integral nut in the vice body. A top quality vice at an economical price. Boxed. Jaw Width: 175mm (7in). Jaw opening: 165mm (6.1/2in).

Vice fixing kit suitable for Record 52PD vice (210-107).

Japanned steel roundhead slotted screws in boxes of 200.

Zinc plated for use into chipboard etc.

Polish for non-grained hard plastics, plexiglass or macrolon, polyester and acryl. 1 litre.

Medium Wire Wool grade 1/2

Bars are approximately 0.9kg unless otherwise stated. Specifically for plastic such as acrylic. 0.8kg bar.

High Tensile and Black Mild Steel. M4 and M5 are high tensile steel. M6 and M8 are black mild steel.

High Tensile and Black Mild Steel. M4 and M5 are high tensile steel. M6 and M8 are black mild steel.

Steel Nuts zinc plated pack of 100

Steel Nuts with a nylon insert.

Roundhead brass slotted wood screws in boxes of 200.

Countersunk brass slotted screws in boxes of 200.

High Tensile and Black Mild Steel. M4 and M5 are high tensile steel. M6 and M8 are black mild steel.

High Tensile and Black Mild Steel. M4 and M5 are high tensile steel. M6 and M8 are black mild steel.

For spindle polishing machines. Made from white cotton with 60 folds giving a mop approximately 1inch wide. Available either stitched for hard use or unstitched for finishing.

PVC carrier tape specifically used for bonding plastics to plastics and is ideal for holding material to CNC machine beds etc.

With a low level tack, this masking tape won't leave any marks when it's peeled. The tape can also be drawn on to mark specific areas. Pack of 12 50m x 25mm rolls.

Quality masking tape in three widths. 50m long.

PVC carrier tape specifically used for bonding plastics to plastics and is ideal for holding material to CNC machine beds etc.

Steel, chrome finish. Jam-proof mechanism, visual refill window, easy refill and doublelever operation. Uses all sizes of T50 staples. (1/4, 5/16, 3/8. 1/2, & 9/16in)

Boxes of 1250 staples, for above staple guns.

Cast aluminium body.

Grit: 80 Size: 533 x 75mm

Mild Steel Rod - 4mm diameter, 1500mm Length.

Class pack of 30. Create perfect 3D sketches in seconds with IsoSketch. The ideal tool for beginners, design students and professionals. IsoSketch combines all the templates and stencils needed to create perfect isometric drawings in seconds. IsoSketch is a 100% British designed, manufactured and distributed product. • 30 IsoSketch 3D drawing tools • Classroom stacker with carry handle • Introduction Powerpoint, A4 learning worksheets (PDF), A5 display postcards (PDF), and tutorial videos available online.

Designed to fit holes drilled with dowel drills to provide accurate markings for drilling the other holes. Packs of 4 points.

• Extra-value classbox of 288 pencils • 12 assorted colours per box • Standard size hexagonal polished barrel • Quality wood with 3mm lead diameter • Display box - Ideal for classroom use!

A vinyl glove for industrial use. Size 9 - 9.1/2

Glue Sticks Cool Melt 0.5kg Pack. 100mm length. Contains approx 28 sticks. Suitable with Bostik cool melt glue gun.

Clean and hygienic these storage units enable easy visual management of stock. Ideal space saving storage unit for safety spectacles and goggles, suitable for laboratories, visitor centers, factories & schools. Each storage unit holds either 24 goggles or 24 safety spectacles.

Pre-assembled fully functioning uncased 4GB memory stick. Ideal for students wanting to design their own case. Easily incorporate electronics into a design project. • Dimensions: 45 x 14 x 4.5mm thick • Write speed 3M/s. Read speed 10M/s • Onboard LED indicator

• Easy-Clean Polypropylene Shelves • 4 x Quiet Heavy-Duty Braked Castors • Flat Packed for Easy Assembly • Maximum weight capacity: 150kg • Dimensions : 960(h) x 415(w) x 830(d)mm • Weight : 11.2kg

Steel blade at 45 degrees. Made in Sheffield.

High quality interior grade lower resin content ply. Measures 500 x 375mm and comes in packs of 12 sheets. *Due to the varying resin content present in this natural product, we cannot guarantee its suitability for use with laser cutters. PLEASE NOTE: While every effort is made to ensure that all sheets are completely flat, as ply is a natural product, 100% flat sheets can't always be guaranteed and some bowing/warping should be expected. If using on a laser cutter, you may need to tape the sheet down for acurate cutting, depending on the bowing. To reduce the risk of warping, Ply sheet should be stored flat in a temperature of approximately 20°C with relative humidity of air about 60%. No tolerances on warping can be given, see the downloads tab for further information.

Contains 30cm clear plastic rule, 180° protractor, 1 each 60/30° & 45° set squares 200mm.

High quality woodworking adhesive and medium made for us to BS4071. Dilute with water to the desired consistency, suitable for gluing a wide range of materials from wood to card and paper. It washes from clothes.

Light pressure of a brush on the dispensing dish instantly pumps the desired amount of solvent. Made from stainless steel and polythene.

The kit contains eight separate moulds and comes complete with MDF baseboard, plastic skin material and a can of spray adhesive to bond them to the cut foam blocks. The moulds included are for a salad server, clock, child's chair, 75mm radius and 125mm radius.

Copic Markers are the original line of high quality illustrating tools used for decades by professionals around the world. These refillable pens feature replaceable nibs and give a lifetime of use. Computerized colour matching and strict manufacturing standards have provided over 25 years of guaranteed colour consistency, which means that Copic inks never vary from batch to batch. Copic Markers have two tips to cover a wide range of uses; a chisel-style tip at one end and a brush tip at the other. The Markers utilize permanent, non-toxic, alcohol-based ink and are also available in a wide style that can easily cover large areas. Colour Range: This set contains the following colours: G17 - B14 - B29 - B39 - E09 - 100 - V09 - RV11 - R08 - YR04 - Y13 - YG03. Box Contains: 12 x Copic Markers

• Spring loaded sheet clamp strips • Parallel drafting arm marked in mm • Automatic locking mechanism • Guide rails on all four sides • Silicone coated for wear free operation

Coloured card A2 100 x 230 micron pack fo 100.

Copic Markers are the original line of high quality illustrating tools used for decades by professionals around the world. These refillable pens feature replaceable nibs and give a lifetime of use. Computerized colour matching and strict manufacturing standards have provided over 25 years of guaranteed colour consistency, which means that Copic inks never vary from batch to batch. Copic Markers have two tips to cover a wide range of uses; a chisel-style tip at one end and a brush tip at the other. The Markers utilize permanent, non-toxic, alcohol-based ink and are also available in a wide style that can easily cover large areas. Colour Range: This set contains the following colours: C0 - C1 - C2 - C3 - C4 - C5 - C6 - C7 - C8 - C9 - C10 - 100 12 x Copic Markers

Assorted pack containing 12 sheets each of blue, red, green and yellow. • Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour • Assorted pack of blue, red, green and yellow

Styrofoam block is fine grain and can be sawn, carved and sanded to shape. It can be glued together using a water based contact adhesive such as item 110-121. Pack of 3 consisting of 2 x 1200 x 600 x 50 sheets and 1 x 1200 x 600 x 75mm sheet.

Money saving bulk pack containing 10 sheets of 1000 x 500 x 3mm opaque cast acrylic. Contains two each of red, blue, yellow, green and 1 each of black and white. Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Packs of 100 sheets of box card.

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

Replacement Needle for 110-220

This kit is designed for Workshops to learn about Arduino, Sensors, Actuators, Coding and Design. It includes a full how-to guide online, and comes with the following: YourDuinoRoboRED Arduino-UNO-compatible with built-in 3-pin I/O connectors, higher-current 5.0V and 3.3V supply. 1 x Bluetooth Radio remote interface: connect to Smartphones etc. 5 x Big push-button switches [Digital Input] 2 x 10K Potentiometers that fit breadboard well [Analog Input] 5 x 10K Photo Resistors (Light sensors) [Analog Input] 1 x Ultrasonic Distance Sensor [Digital Signal Input] 1 x Joystick Module {Analog Input] 1 x Digital temperature sensor DS18B20 [Digital Signal Input] 1 x LCD Display 2 lines of 16 characters [Signal Output] 50 x LEDs - 5 assorted colours, plus 10 220 ohm resistors (below) [Digital or Analog Output] 1 x Red-Green-Blue Multicolour LED [Digital or Analog Output] 1 x Buzzer Module (makes sound with voltage applied) [Digital Output] 1 x Beeper Module (Makes different sounds/tones with Arduino TONE Library) [Analog Output] 1 x Servo Motor (Mechanical positioning from digital pulses] [Digital Signal Output] 1 x Small Stepper Motor with driver board [Digital Signal Output] 1 x DC Motor small 5V 1 x Power Transistor NFET (Can control DC motor, other large DC loads) 2 x 3-pin cables to 3-pin connectors that fit the Robo1 and various Electronic Bricks etc. 2 x 3-pin cable to separate wire ends that connect the Robo1 to any device 1 x USB Cable (50cm) 1 x 40 wide flat rainbow color cable that can be separated to make many different cables 2 x 40 pin strips that can be separated to connect cables to breadboard and other devices 10 x 220 ohm resistors (LED current limit etc.) and 10K resistors (switch pullups etc.) 1 x 8cm high-quality Breadboard with power and ground strips

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Lino - 30mm overall with a 28mm particle board core with a 2mm linoleum surface complete with durable plastic edgebanding. An easy clean, general duty top ideal for office, assembly and storage areas. • Robost steel section framework with corner bracing • Height adjustable frame • 30mm worktop • Optional storage units available • Comprehensive self assembly instructions included • Powdercoat RAL7035 grey finish • Built to last 10 years guarantee HxWxD: 780 - 930 x 1500 x 600mm

Money saving bulk pack containing 3 x 1kg sticks.* With a melting point of 240°C, this is an ideal material for teachers to demonstrate casting techniques and processes to make highly detailed items such as jewellery, tankards, coasters, place mats, trays etc. Being non-toxic and totally re-useable it is an ideal material for schools. *The weight of one stick is approx 1kg Alloy conforms to BS EN 611-1:1996 Alloy 3 Lead Free Pewter.

Features and Benefits • High power 175W motor for high performance • Soft grip in all gripping areas for better handling • Full variable speed control (5.000-35.000 RPM) for maximum precision • Electronic feedback for enhanced torque and performance • Separate on/off switch with integrated collet lock out function Contents • Dremel 4000 • Pencil grip nose cap • High quality Flex Shaft • Line & Circle Cutter • Shaping Platform • Detailer's Grip • 65 High quality Dremel accessories in Mini Accessory Case (including SpeedClic starter set) • Inspiring welcome poster • Instruction manual • Sturdy and spacious storage space **NOTE: includes collet 3.2mm** Technical specifications Rated power input: 175 W Voltage: 230 V Weight :0.66 kg No load speed:5.000 - 35.000 1/min

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Polyethylene foam has the added advantage of being available in thicker sheet sizes without having to be laminated.

This is a very high density material with a close structure. Suitable for prototyping, modelling, patterns and CNC milling & cutting. It is strong and provides good surface detail and can also be used as a mould for vacuum forming. Modelling board can be both painted and glued. Sheet size: 250 x250 x 50mm

Great roundness and consistency, PLA is Poly-Lactic-Acid, a biodegradable polymer that has a low melting point. It is an amazing material to print with and you can print at very high speeds when using this material.Ultimaker filaments have endlessly been tested to ensure they are up to the job: only the best make the grade. Prints come as intended time and time again.Ultimaker PLA is really easy to print with, it's reliable, gives good surface quality and it's made from renewable sources, so it's biodegradable too. It also works perfectly with Cura material profiles. • If you want to easily achieve high resolution prints • Printing concept models and prototypes when aesthetics and fine details are key • When you're casting metal parts through lost PLA casting • It's perfect for printing in education or in the office, thanks to low ultrafine particle emissions • A heated bed isn't necessary, it works with glue and blue tape as well • PLA isn't suitable for medium temperature applications (50°C +) or long term outdoor usage. ABS is a better material for high temperature applications and CPE for outdoor usage.

Great roundness and consistency, PLA is Poly-Lactic-Acid, a biodegradable polymer that has a low melting point. It is an amazing material to print with and you can print at very high speeds when using this material.Ultimaker filaments have endlessly been tested to ensure they are up to the job: only the best make the grade. Prints come as intended time and time again.Ultimaker PLA is really easy to print with, it's reliable, gives good surface quality and it's made from renewable sources, so it's biodegradable too. It also works perfectly with Cura material profiles. • If you want to easily achieve high resolution prints • Printing concept models and prototypes when aesthetics and fine details are key • When you're casting metal parts through lost PLA casting • It's perfect for printing in education or in the office, thanks to low ultrafine particle emissions • A heated bed isn't necessary, it works with glue and blue tape as well • PLA isn't suitable for medium temperature applications (50°C +) or long term outdoor usage. ABS is a better material for high temperature applications and CPE for outdoor usage.

High quality interior grade lower resin content ply. Measures 500 x 375mm and comes in packs of 12 sheets. *Due to the varying resin content present in this natural product, we cannot guarantee its suitability for use with laser cutters. PLEASE NOTE: While every effort is made to ensure that all sheets are completely flat, as ply is a natural product, 100% flat sheets can't always be guaranteed and some bowing/warping should be expected. If using on a laser cutter, you may need to tape the sheet down for acurate cutting, depending on the bowing. To reduce the risk of warping, Ply sheet should be stored flat in a temperature of approximately 20°C with relative humidity of air about 60%. No tolerances on warping can be given, see the downloads tab for further information.

High Speed Steel Roll Forged drills, are suitable for drilling in a range of materials such as metal & plastic. They can be used in hand and power drills. A suitable lubricant & PPE is always recommended. Size: 1.5 Flute length: 18mm Length: 40mm

High Speed Steel Roll Forged drills, are suitable for drilling in a range of materials such as metal & plastic. They can be used in hand and power drills. A suitable lubricant & PPE is always recommended. Size: 2mm Flute length: 24mm Length: 49mm

High Speed Steel Roll Forged drills, are suitable for drilling in a range of materials such as metal & plastic. They can be used in hand and power drills. A suitable lubricant & PPE is always recommended. Size: 3mm Flute length: 33mm Length: 61mm

• HSS-R roll forged 4341 high speed steel. • Manufactured to DIN338 with 118° point. • General purpose 'jobber' drill bits for drilling steel, aluminium, non-ferrous metals, plastics and wood. Use cooling agent and drill at slow speeds for best results in metals. Pack of 10 Size: 4mm

• HSS-R roll forged 4341 high speed steel • Manufactured to DIN338 with 118° point • General purpose 'jobber' drill bits for drilling steel, aluminium, non-ferrous metals, plastics and wood • Use cooling agent and drill at slow speeds for best results in metals. Pack of 10.

• Packs of 25 sheets • Silicone carbide paper sheets. Latex quality • Sheet size 280 x 230mm

Heavy duty belts for use on wood, plastics & fillers. Sold singly. Size - 1090 x 150mm

Quality Hardwood Dowel from sustainable sources. Pack of 10, 10mm diameter, 600mm long. Nominal size ± ½ mm.

Quality Hardwood Dowel from sustainable sources. Pack of 10, 6mm diameter, 600mm long. Nominal size ± ½ mm.