TSL - Technology

The standard tilting table is 226 x 278mm and indexed 135-90°. The integral dust extraction system significantly improves performance and combined with cassette collection and disposal enhances easy, convenient waste handling. Fully compliant with UK COSHH regulations, the European Machinery Directive and also with the BS4163:2014 Health and Safety in Workshops of Schools and Similar Establishments” Regulations. Supplied and fitted with a medium grade, grit belt. KEY FEATURES • Dust extraction mounted • Quick action calibrated tilting table for operating positions between 90 and 135 degrees • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 150 x 1090mm aluminium oxide abrasive belt

250mm dia blade for MACC-TE250.

With a cast iron table at the heart of this compact machine it is designed to offer those with limited space or budgets a real bandsaw with sensible capacity and performance, as an alternative to lightweight hobby machines. It shares the same essential build qualities as its larger cousins, strong steel frames, dynamically balanced bandwheels, cast iron tables and an induction motor. It has been designed to offer the user with space restrictions a serious machine in compact form. Key Features: • Blade Guides - Simple to set and easily adjustable • Sealed for life bearings - Require no maintenance during the life of your machine • Capacity - Large 120 mm depth of cut and 240 mm throat depth make this a compact machine capable of serious work • Strong Fence - With cam action lock for ease of use and simple tension adjustment for clamping strength (clamps at rear of table) • Table - A solid, finely ground cast iron table provides an ideal and low friction work support • Trunnion - Table tilts from 0 - 45º on a solid trunnion with easy to read scale Specification: Maximum Depth of Cut: 120mm Throat Depth: 240mm Table Size: 315 x 350 mm Table Height from Floor: 370 mm Motor Power: 1/2 hp Blade Length: 70 1/2"" Blade Width Capacity: 1/4 - 1/2"" Blade Speed: 740 M / minute Extraction Port Diameter: 58 mm (100 mm with supplied adaptor) Height: 860mm Width: 550mm Depth: 480mm Weight: 30kg

Features: • Movable Head 45° right & left • Reduction unit in oil bath • Membrane pump for coolant • Coolant filter • Vice complete with anti-burr device • Bar stop • 24 Volts low voltage installation with hold-to-run head control knob • Service tools • Instruction manual & spare parts

Pedestal for MACC-TE250

Image shows dust extraction unit incorporated into machine bench.

Programmable spindle speeds and feedrates make the VMC 1300 ideal for cutting a range of resistant materials such as wax, plastic, acrylic, free cutting alloys, aluminium and steel. Also available for integration into FMS/CIM systems (additional equipment must be fitted at the time of manufacture. The VMC 1300 comes as standard with: • VR CNC Milling Operating Software (PC not included) • Installation and instruction manuals • Power Drawbar with manual actuation • Workholding clamps • USB connection

The machine can be supplied for left or right handed operation and for a small surcharge it can be supplied with the necessary parts for easy conversion in the workshop. TECHNICAL DATA • Drilling capacity in mild steel 13mm • Motor 0.25kW Single phase • Throat depth 194mm • Speed range 500-4000rpm • No. of speeds 5 • Table size 235 x 409mm • Dimensions 815 x 372 x 627mm • Weight 46Kg KEY FEATURES • Made in the UK • Bench mounted • Easy to use • Front mounted controls • Head raising mechanism

The machine can be supplied for left or right handed operation and for a small surcharge it can be supplied with the necessary parts for easy conversion in the workshop. TECHNICAL DATA • Drilling capacity in mild steel 13mm • Motor 0.25kW Single phase • Throat depth 194mm • Speed range 500-4000rpm • No. of speeds 5 • Table size 235 x 409mm • Dimensions 815 x 372 x 627mm KEY FEATURES • Made in the UK • Bench mounted • Easy to use • Front mounted controls • Head raising mechanism • Latching footswitch

The TSFLA has exceptionally low noise characteristics for use within the classroom and is designed for use with fine dusts. Warm air is returned to the classroom being sympathetic to environmental issues. A certified explosion vent relief panel is supplied to meet local authority or HSE requirements. The Top Extraction Kit is available from Technology Supplies for installation by our engineers. Please specify inlet port diameters and saw model number at time of order placement. These products require specialist installation & training. Please contact us for further information.

The TSHS has a primary dust separator in the form of a cyclone, which removes the bulk of the extracted dust, leaving relatively clean air to pass through a secondary cartridge fi lter, thus extending fi lter life. The TSHS has exceptionally low noise characteristics for use within the classroom and is designed for use with fi ne dusts. Warm air is returned to the classroom being sympathetic to environmental issues. A complete installation service is available from our engineers. These products require specialist installation & training. Please contact us for further information.

The TSPL may also be used for other similar applications and offers the designer a realisticn alternative to a Centralised Ducted System. The TSPL has exceptionally low noise characteristics for use within the classroom and is designed for use with coarse dusts, hence the large collection bin capacity and the comparatively low footprint area of the machine. Warm air is returned to the classroom being sympathetic to environmental issues. A cerfified explosion vent relief panel is supplied if required to meet local authority or HSE requirements. Extraction Kits for Planers and Wood Lathes are available from Technology Supplies for installation by our engineers. Please specify inlet port diameters, locations (LHS/RHS) and lathe/planer model at time of order placement. These products require specialist installation & training. Please contact us for further information.

Mobile stand on heavy duty lockable castors.

Ni-Chrome wire 20swg x 10m for sculpture tool & Models 600 1000 hot wire Strip Heaters.

The key to quality is good preparation. It can make the difference between a success and failure. Why? Because poorly heated materials does not perform as well, increasing your costs if you have to start again. The C R Clarke 200FD is designed by plastic forming experts. Digital controls mean precise heating. And the mix of a circulated fan and insulation maintains consistent heat. The result. Material which work ready, so your students can get straight on with their projects. Ideal for heating materials for dip coating, dome blowing, press forming and thermoforming. Key features: • Internal capacity 508 x 355 x 304mm • Heats up to 350°C - Perfect for thermoforming plastics and pre-heating • Digital control - Achieve the ideal temperature for processing • High quality, asbestos-free ceramic fibre wool insulation - A consistent temperature means better quality and less waste • Single phase - Plug in any socket or hard wire to a switched outlet • No volt release and overload protection - Keeping safety in the classroom paramount

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

Compact and affordable. C R Clarke 1210 vacuum former is an ideal entry level machine. Its smaller forming area means lower cost for materials. Perfect for first time users and simple model making. 240V, single phase. Key features: • 4 independent ceramic heaters - Balance out temperature variations across four zones • Interlocked guard - Moving parts are safely contained while allowing good visibility of the forming process • Blow release - Remove parts from mould without effort • No-volt safety switch - Automatically isolates machine in the event of power failure Included items: • C R Clarke 1210 vacuum former machine • Starter pack of material

Turn your C R Clarke 1210 vacuum former into a mobile workstation. Sturdy, easy to move, and features a storage shelf to keep all accessories to hand. Ideal for small departments where worktop space is limited.

This machine is a perfect mid-range vacuum former, ideal for schools and model makers. It has a smaller forming area than the C R Clarke 750FLB, and is desktop mountable. 240V, single phase. Key features: • Independent ceramic heaters - Balance out temperature variations across four zones • Interlocked guard - Moving parts are safely contained while allowing good visibility of the forming process • Digital timer with alarm - Monitor the cycle more efficiently • Blow release - Remove parts from mould without effort • No-volt safety switch - Automatically isolates machine in the event of power failure * Reducing frame available - Decrease the forming aperture Included items • C R Clarke 725FBL vacuum former machine • Starter pack of material

Reduces the standard forming area of the C R Clarke 725 and 917 vacuum formers from 228 x 432mm to 228 x 216mm.

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

Turn your C R Clarke 725 vacuum formers into a mobile workstation. Sturdy, easy to move, and features a storage shelf to keep all accessories to hand. Ideal for small departments where worktop space is limited.

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

The 320 Dome Blowing Unit consists of a rigid base with a heat-proof seal plate that has perforations to allow air to be injected. A sheet of thermoplastic material, normally cast acrylic, is heated in an oven to its softening temperature. The material is transferred to the Dome Blowing Unit and is clamped into position. Air is blown under the sheet using the control valve on the front panel, inflating the dome. An adjustable height gauge assists the user to achieve consistent dome heights. Once cooled, the dome is unclamped and is immediately ready to use. The 320 requires an external air supply, this can come from a compressed air supply or the Pressure Outlet of one of our Vacuum Forming Machines. The 320 is supplied with rings to make domes of 300, 225 and 150mm in diameter.

It uses a 125 watt motor and router bit combination mounted in a unit measuring 355 x 380 x 380mm. The combined fence and guard protects the user from the cutter and enables fine detail to be trimmed safely. It will trim right up to an edge or leave a flange as desired. Single phase industrial motor. Swarf collection duct. Angled work support table. Foot switch operated for safety. Supplied with 3mm dia. slot drill.

The 280 has a fine heating wire capable of cutting expanded polystyrene materials up to 250mm in thickness. Variable power to the wire is supplied from the low voltage transformer housed in the base of the machine. Freehand shapes can be cut with ease, while the machine table also has grooves to accept the accessories supplied with each machine: • Parallel Guide • Protractor Guide for non-parallel cuts • Circle Cutter

Fluidised baths consist of a tank to hold thermoplastic powder, a plenum box and a porous membrane. When low pressure high volume air is blown through the powder via the plenum box it causes the powder to lift and disperse thus behaving like a liquid and permits immersion of a preheated metal component. • Everything needed to carry out dip coating with plastic powders • Contains: Model 300 and 150 fluidised bath, Model 120 blower unit and stand • 670 x 700 x 770mm

A kit of parts for replacing the silicone seals etc on popular vacuum formers. If your machine is not performing well, the filter may also need replacing. Includes silicone seal, platen seal filter element & adhesive

Jacobs No.6 internal taper and K3 key.

For Craft & Supercraft chucks, 13mm & 16mm.

For processing wider boards on the Sedwick TA315 Circular Sawbench.

It has a large cast iron tilting fence for accuracy and timber support, front and rear cutterblock guards, shaw guards for rebating and features an enclosed drive mechanism. A no-volt release starter with thermal overload, key switch, footswitch and anti-kick back fingers for thicknesser are fitted as standard. KEY FEATURES • Two Knife Cutter block • Cast Iron table • Cast Iron fence • 180 x 255mm thicknessing capacity • 255mm surfacing width • Footstop and key switch included • UK Manufactured

Whether deep ripping or cutting the most intricate shapes, the design features of this machine ensure it is done precisely and effortlessly. • Two speeds 800 and 1200 m/min for the most varying materials • Sturdy cast-iron table tiltable from -20° to +47° • 3-roller precision guiding above and below the table • Upper saw blade guiding by toothed rack, adjustable in its height • Balanced and polished band wheels with rubber facing • Quick-clamping lever for saw blade • Maximum cutting height: 300 mm • Throat 440 mm • Precision rip fence with magnified scale which can be set both left and right of saw blade • 3phase HxWxD: 1930 x 800 x 1140mm Weight: 214kg

The rip fence is aluminium section allowing for two working positions (ripping and angled ripping). It is fixed to a cast iron mounting bracket for rigidity and has integral micro adjustment. A telescopic extension arm is fitted to the cross cut fence for setting the timber stop. The 620mm Cross Cut Table is designed for cutting mitres and compound angles, end trimming, squaring, dividing and trimming. It has a maximum depth of cut 105mm @ 90° and 76mm @ 45°, double sided saw guard with dust extraction outlet, enclosed drive mechanism. Supplied with an anti kick saw blade. Thermal overload, no-volt release switch, lock off emergency stop switch and foot operated foot switch are fitted as standard. Fitted with keyswitch.

This machine features a temperature controlled heating barrel, rack and pinion injection ram, over centre mould closing, automatic moulding ejection and is supplied with a wheel mould (flat upper & shaped lower mould) and 2kgs of red polystyrene granules. To operate the machine, plastic granules are loaded into the heating barrel. After a short pre-heat time, the plastic is ready to inject. The mould is closed and the injection ram lowered. This action automatically opens a valve in the injection nozzle and the plastic is injected. Once the mould is full the ram is retracted. The heating barrel rises on its return springs, closing the valve. After cooling the mould is opened and the moulding is ejected by pins in the mould cavity. Requires permanent fixing or bolting down. Safe and easy to use.

The 180 combines a heated wire on a tensioned bow, ideal for cutting expanded polystyrene models, with a horizontal wire or strip heating of rigid plastic materials. This compact unit is ideal for smaller workshops.

Service kit for replacing silicon seal on the CR Clarke 1210 Vacuum Former. Service kit includes: silicone seal, platen seal, adhesive, and primer. NOTE: If your machine is not performing well, the filter may also need replacing.

A kit of parts for replacing the silicone seals etc on popular vacuum formers. If your machine is not performing well, the filter may also need replacing.

This folding jig from C R Clarke is a useful accessory to their range of strip heaters. The jig has a working length of 600mm and is adjustable from 160° obtuse to 30° acute. The jig's calibrated protractors ensure consistent setting, with hand knobs for easy adjustment. The adjustable work stops can also be used to hold the material in the folding jig, allowing the operator to continue with other work while the folded material cools.

Expert II Series is an excellent choice for beginners and provides optimum speed, superior quality, solid reliability and unmatched value. Expert II produces eye-catching graphics with up to 27.8 ips cutting speed, 350g of cutting force and 3 metres (9.84 feet) of tracking ability. The versatile Expert II Series sets a new benchmark for value, offering high accuracy and reliability at an unbelievably affordable price.

The PCB Engraver is supplied with operating software incorporating Gerber and DXF import facilities. The PCB engraver is ideal for cutting and engraving a range of resistant materials, including copper board, plastic and acrylic. • Powerful operating software that is simple to use and allows multiple design to be made at once • High speed spindle motor and floating head • Basic tools and depth-setting device • Installation and Instruction guides • Outlet for dust extraction • Sacrificial Table • USB Connection Optional Equipment: CAD, CAM and/or PCB design software, such as Denford’s QuickCAM 2D Design, will be required in order to make the files required for machining (CNC G-Code or Gerber).

Mild Steel Rod 8mm diameter, length 1500mm.

Mild Steel Flat Bar 10 x 3mm, length 1500mm.

Mild Steel Flat Bar 25 x 3mm, length 1500mm.

Mild Steel Flat Bar 30 x 3mm, length 1500mm.

Mild Steel Flat Bar 12 x 3mm, length 1500mm.

Mild Steel Rod 3mm diameter, length 1500mm.

Tin/Bismuth low temperature casting alloy which has a melting point of 138°C, this is an ideal material for students to practice casting techniques and processes to make items such as busts or figure heads. Being non-toxic and totally re-useable it is an ideal material for schools. Due to the melting point temperature, wooden patterns or plaster of paris moulds can be used. (Pack 4 Tinsmans Sticks).Suitable for the low temperature casting system. Sn 43% / Bi 57%

Mild Black Steel Flat Bar 50 x 3mm, length 1500mm.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 305mm, length 10m.