Timstar

Designed with safety and ease of operation in mind making it ideal for use in education. Two samples can be tested simultaneously. Built-in illumination and viewing magnifying lens give clear viewing of samples. Temperature range: Ambient to 300°C. Three digit LED display. Resolution is to 0.1°C and temperature to melt is variable from 1-10°C. For 220/240 V. Dimensions (L x W x H): 160 x 220 x 170mm.

An aluminium block with an angled hole drilled to accept thermometer (not included). Dimensions (Diameter x H): 65 x 50 mm.

Soda Glass. Outside diameter 1.8-2.0 mm. Wall thickness 0.28-0.32 mm. In packs of 100.

Soda Glass. Outside diameter 1.8-2.0 mm. Wall thickness 0.28-0.32 mm. In packs of 100.

The SDS5032E is a general purpose 2 channel digital oscilloscope with large 200 mm colour display, making it ideal for education and industrial environments. Complete with USB output to PC. Specifications and Features: • Bandwidth: 30 MHz • Sample Rate (real time): 250 MSa/s (125 MSa/s per channel) • Memory depth: 10 KB • Maths functions: Add, subtract, multiply, division and FFT • 20 automatic measurements • Auto-scale function • Standard interface: USB, USB flash drive, LAN, VGA • Bandwidth: 30 MHz • Waveform storage: 15 waveforms • Vertical Sensitivity: 5 mV/div~10 V/div (at input) • Vertical resolution: 8 bit • Trigger Type: Edge, Pulse, Video, Slope • Trigger Mode: Auto, Normal, Single

The Spider power supply has been specifically designed for primary, middle and lower secondary school use. Offering 1.5, 3, 4.5 or 6 V smoothed and regulated DC at up to 1 A, it is the ideal next step from using cells and batteries. Four sets of terminals mean it can be used by four groups simultaneously enabling children to connect a multitude of low voltage electrical devices with the spider's bright LED's acting as power output monitors. •Manufactured in the UK •No batteries needed •4 x 4 mm output terminals •Compact and safe design •Fun to use

A compact power supply offering 2, 4, 6, 8, 10, and 12 V at currents of up to 5 A. Both DC and AC outputs may be used simultaneously up to the rated output. The output is protected by a push button cut-out. The unit is 2 A fused on the back panel and comes complete with a moulded mains lead and plug. 4 units are designed to fit in a shallow Gratnell tray. Specification •Input Supply voltage 230 V DC •Supply frequency 50 Hz •Mains fuse Rear panel 2 A, 20 mm quick blow Mains plug 3 A •Output Voltage 2, 4, 6, 8, 10, 12 V AC nominal 1, 3, 5, 7, 9, 11 V full wave rectified DC nominal •Maximum output current 5 A AC or DC •Manufactured in the UK

The Powerlock power supply has both lockable AC and DC outputs ranges by a simple key making it impossible for students to change the voltage. The Powerlock offers 2, 4, 6, 8, 10 and 12 V in both DC and AC. Outputs may also be used simultaneously up to the rated output required. For safety, the output is also protected by a simple push button cut-out. Supplied with 2 keys. •Output voltages AC & DC •2, 4, 6, 8, 10, 12 V range in AC and DC •Current 5 A •Voltage type - Stepped •Output type - Full wave rectified, non-regulated •Push button trip reset •Mains input 230/240 V AC, 50 Hz •Supplied with mains plug and lead •Manufactured in the UK

The Powerbase is ideal for use in physics, biology and chemistry experiments in secondary and sixth form schools. It comes with a sturdy, powder-coated steel case with fold flat carry handle making it easily stackable. A very popular power supply that has proven to last the rigours of daily use within schools with its tough construction and tamper proof fixings. •0-15 V AC and 0-20 V smoothed DC at up to 8 A •Combined Continuously variable output •Maximum voltage lock push button reset •Short circuit protection •Tough steel powder coated casing •Heavy-duty screw-in rubber feet •Stackable •Supplied with power lead •Designed and manufactured in the UK •5 Year Warranty

A highly versatile power supply for all low-voltage experiments, with continuous voltage adjustment, separate for DC and AC. The two outputs can be loaded simultaneously without interference. Four digital displays show DC and AC voltage and current. The continuously adjustable DC current limiter can be set using a screwdriver. There is an LED indicator to show when the selected maximum current is reached. The power supply also features electronic overload protection. Specifications DC Output voltage: 0-24 V (stabilised) Ripple and noise (max): 25 mVpp Output current (max): 10 A (0-12 V) Max output current falls linearly to 6 A at 24 V Electronic, continuously adjustable current limiter, adjusted with screwdriver AC Output voltage: 0-24 V (stabilised sine) Output current (max): 6 A Electronic current limiter

The perfect choice for experiments with, for example, electron beam tubes requiring voltages up to 500 V DC at a low current level. The unit also provides two auxiliary outputs: A continuously variable negative voltage (down to -50 V DC), series connected with the 500 V output, and a stepwise selectable AC voltage with galvanic isolation from the DC outputs. Continuous adjustment of the -50 V and 500 V voltages. The current is limited to 50 mA. Voltage and current can be read from separate displays. A switch selects which output to monitor. The AC output delivers up to 3 A and is provided with a thermo fuse. Note: Not recommended for students due to high output current. Specifications Negative DC voltage: 0 to -50 V Current (max): 50 mA Positive DC voltage: 0 to +500 V Current (max): 50 mA Ripple: less than 0.1% Regulation: Better than 1 % for variations in mains voltage and load up to 10 %. AC Voltage: 2 to 7 V (1 V steps) Current (max): 3 A

This power supply delivers stabilised DC voltage, continuously adjustable between 0 and 6 kV. For safety, the current is limited by a built-in series resistance. The short-circuit current is 2 mA max. Under load, the voltmeter shows the actual supplied voltage. The power supply is also capable of delivering 6.3 V (max. 3 A) AC. This is the standard voltage for many electron tubes etc. On the front, you find a yellow/green ground socket, connected to the metal enclosure and hence (through the mains wire) to earth. The high voltage section floats relative to ground, allowing either the black (negative) socket or the red (positive) socket to be connected to ground, resulting in a voltage range of 0 to +6 kV resp. 0 to -6 kV relative to ground. Specifications •DC Voltage: 0 - 6 kV. Stabilised, continuously adjustable •Short-circuit current (max): 2 mA •Ripple and noise (max): 1% (RMS, 100 V - 6 kV) •Read-out precision: 1% + 1 digit •AC Voltage: 6.3 V •Current (max): 3 A

This power supply delivers stabilised DC, continuously adjustable from 0 to 12 V. It also supplies AC, selectable between 2, 4, 6 and 12 V. The AC voltage is not stabilised. Both outputs have overload protection. The DC channel is electronically protected and automatically reconnects while the AC channel has a circuit breaker which must be manually reconnected if it trips. Specifications •DC Output voltage: 0 - 12 V (stabilised) •Ripple and noise (max.): 100 mV •Output current (max.): 3 A •AC Output voltage: 2, 4, 6, 12 V •Output current (max.): 3 A

A simple, robust and reliable power supply, ideal for basic electricity experiments. It offers stepped adjustment of both AC and DC with 1 V between the steps. The DC voltage is not smoothed or stabilised, meaning there is a fluctuation of approx. 10% of the output voltage at step level. The unit is protected against overload with an automatic circuit breaker (the unit works again after about 10 seconds). DC voltage: 1 to 12 in 1 V steps Current: 6 A max AC voltage: 1 to 12 in 1 V steps Current: 6 A max

This has to be the best signal/function generator available for educational use! Developed in conjunction with physics teachers and designed specifically for education, this unit provides all the functionality you need for physics teaching. really useful feature for those less familiar with using signal generators is that for basic use, you just operate two buttons: One for frequency and one for amplitude that's it! There is, of course, far more sophistication for those who require it. If you want to change waveform or to utilise the step and sweep modes, the display keeps you updated on the status of the generator. Unique frequency control: The frequency is set by speed sensitive button. Turn slowly to set the display's last digit, turn faster and the response accelerates designed to work intuitively in practical experiments. Drives speakers, vibration generator etc. directly: The built-in 10 power amplifier effortlessly drives power appliances e.g. vibration generator. The amplifier can deliver more than amp for all frequencies between 0.001 Hz and 100 kHz. Step mode: In many applications you need to study physical system at fundamental frequency and at different multiples of that frequency. The special step feature makes this task incredibly easy. Once the fundamental frequency has been determined (e.g. of spring connected to vibration generator), other harmonics (or overtones) can be demonstrated by simply pressing button, which changes the frequency to progressive multiples of the fundamental frequency. Sweep mode: The generator can sweep through frequency range in order to discover eventual resonances. You decide the frequency range and the speed. You have the choice between linear sweep (fixed number of Hz per unit time) and logarithmic sweep (fixed number of octaves per unit time). Advanced Features: The generator connects to your PC through standard USB cable and acts as USB flash drive. Custom defined waveforms (e.g. created by means of spreadsheet) can be saved to the generator. Sequences of settings can be programmed for automatic execution.

A high-quality simple-to-use student signal generator with a range of applications. Operated with just three buttons: Waveform, Frequency and Amplitude. There is a single output, provided with 4 mm safety sockets. The output can easily drive a speaker or vibrator with ample amplitude for resonance and diffraction experiments. The frequency range extends well beyond the audible range. The lowest frequencies are suitable for ""slow motion AC"" experiments. Unique frequency control The frequency is set with a speed-sensitive button. If you turn slowly, the last digit of the display is set. Turning faster, the response accelerates smoothly. The generator covers the six decades from 0.05 Hz to 50.00 kHz in a single range. The frequency is stable within 0.005 % Three waveforms The generator provides sine, triangle, or square wave signals. Distortion of the sine wave is less than 0.25 % in the audible range (20 Hz - 20 kHz) and remains below 1 % throughout the frequency range (0.05 Hz - 50 kHz). Built-in power amplifier The signal amplitude is continuously adjustable from 0 V to a peak voltage of 7.5 V (15 V p-p; 5.3 V RMS). More than 1 A peak current can be supplied. The output is overload protected. Supplied with 12 V power adapter.

Voltages of 0 to 30 V DC and 0 to 300 V DC at up to 60 mA. Outputs are fully floating to provide negative voltages if required and are taken from pairs of colour-coded 4 mm sockets on the front panel. Each output has a continuously variable voltage control, with electronic current limiting circuitry. An indication of the output voltage is given by a graduated scale on each voltage control. A pair of 4 mm sockets on the front panel provide 6.3 V AC at up to 2 A for filament heating. An illuminated on/off switch is mounted on the rear panel adjacent to a fused appliance inlet. Housed in a robust metal case with a durable powder coated finish. •DC Output Voltage Range No1: 0 to 30 V DC •DC Output Voltage Range No2: 0 to 300 V DC •Maximum DC Output Current: 60 mA (both ranges) •AC Output Voltage: 6.3 V AC •Maximum AC Output Current: 2 A

A low-cost alternative to dry cell batteries. Housed in a robust ABS plastic case, this power supply is ideally suited as a replacement in applications where batteries are normally used. Smoothed and regulated DC is available over those ranges selected by rotary switch. Output is via 4 mm red and black sockets. The DC output voltage available are 1.5, 3, 4.5 and 6 V DC at a maximum current of 1 A.

Continuously variable 0 to 20 V AC and full-wave rectified DC at maximum 6 A continuously or 8 A for short periods. Resettable thermal cut-out. Outputs from two pairs of colour-coded 4 mm sockets. Output voltage is indicated by means of a calibrated scale. An illuminated on/off switch is mounted on the rear panel adjacent to a fused IEC mains inlet. Enclosed in a robust metal case with a durable powder coated finish. •AC Output Voltage Range: 0 to 20 V AC •Maximum AC Output Current: 6 A (8 A short period of time) •DC Output Voltage Range: 0 to 20 V DC •Maximum DC Output Current: 6 A (8 A short period of time)

This unit provides voltages of 2, 4, 6, 9, 12 or 14 V AC or full-wave rectified DC at 4 A continuously, or up to 5 A for periods of 1 hour. Voltages are selected by means of a rotating switch on the front panel. In any incidence of overload, including direct short, a current sensing circuit breaker mounted on the front panel will operate and disconnect the output voltage. Outputs are taken from colour coded 4 mm sockets mounted on the front panel. An illuminated on/off switch is mounted on the rear panel adjacent to a fused appliance inlet. Housed in a robust metal case with a durable powder coated finish. Supplied with mains lead and instructions. •AC Output Voltage Range: 2, 4, 6, 9, 12 and 14 V AC •Maximum AC Output Current: 4 A (5 A up to 1 hour) •DC Output Voltage Range: 2, 4, 6, 9, 12 and 14 V DC •Maximum DC Output Current: 4 A (5 A up to 1 hour)

Continuously variable output from 100 V to 5 kV DC. Output voltage is indicated on a 14 mm 2-digit LED display. The EHT circuits are fully floating so that for certain applications the positive or negative terminal may be safely connected to earth. The EHT outputs are taken from 4 mm shrouded sockets and provide 100 V to 5 kV DC at up to a maximum of 3 mA or current limited to 60 µA. A centre tapped socket is provided to give ±2.5 kV DC output. An additional pair of 4mm shrouded sockets at 19mm spacing are provided giving 6.3 V AC at 2 A for filament supplies. There is also a separate earthing terminal. An illuminated on/off switch is mounted on the rear panel adjacent to a fused IEC mains inlet. Enclosed in a robust metal case with a durable powder coated finish. Supplied with instructions and detachable mains lead. •DC Output Voltage Range: 100 V to 5 kV DC •Maximum DC Output Current: 3 mA •Maximum DC Limited Current: 60 µA •AC Output Voltage: 6.3 V AC •Maximum AC Current: 2 A Accessories •5 kV Lead Red: EL91360 •5 kV Lead Black: EL91362

This signal generator and amplifier provides sine, square or triangular waveforms. Frequency selection is by a switched range and continuously variable fine adjustment control. The frequency is displayed on an LED display. All connections are via pairs of labelled 4 mm sockets with one of each pair connected to earth. An illuminated on/off switch is mounted on the rear panel adjacent to a fused IEC mains inlet. Enclosed in a robust metal case with a durable powder coated finish. Signal Generator Mode: •Waveforms - Sine, Square & Triangular, sinewave distortion 1% on all ranges, square wave rise time 1 µs approx. •Frequency Range - 0.1 Hz to 100 kHz in six ranges, accuracy ±5% on all ranges •Voltage Output - 0 to 10 V (peak to peak), continuously variable across all ranges & waveforms •4 Ω Output - Power output of 4 W over entire frequency & waveforms, will drive loudspeaker or other suitable devices •600Ω Output - Provides attenuation settings: x 1, x 0.1 & x 0.01, all ±5% Amplifier Mode: •Performance - Voltage gain 0 to 100, Input impedance 1 MΩ, Max. input 200 mV (pk to pk), Output spec. same as above •Frequency Response - Frequency response 1 Hz to 100 kHz (-3 dB bandwidth)

Sine and square wave generator. Frequency range 5 Hz to 50 kHz in four switched ranges plus a fine control. Accuracy typically ±10%. The output amplitude is continuously variable from zero to maximum 8 V peak to peak with maximum output power 1 W into 8 ohms. The output is taken from two 4 mm sockets mounted on the front panel. An illuminated on/off switch is mounted on the rear panel adjacent to a fused IEC mains inlet. Enclosed in a robust metal case with a durable powder coated finish.

The Powerbase S8 offers 0 to 12 V at 8 A via a safe relay switching system that provides voltages in 1 V steps. AC and DC voltages are available simultaneously in any combination up to a combined output of 8 A. The output is safely protected by a thermal cut out switch on the front panel with an output limiter which allows the user to preset the maximum voltage available. 0 to 12 V AC/DC in 1 V steps 8 A combined simultaneous output lockable via an Allen key mechanism. • Maximum output 0-12 V DC & 0-12 V AC • Current 8 A • Supplied with Allen key to lock minimum or maximum output • Voltage selector type - Relay switched • Output type - Smooth non-regulated • Push button trip reset • Mains input 230/240 V AC, 50 Hz • Supplied with mains plug and lead + Allen key • Manufactured in the UK

The Powerbase V8 comes with a high-power rotary transformer and a high specification toroid transformer. The unit supplies 0-20 V smoothed DC and 0-16 V AC at 8 A. The output is continuously variable and protected by a panel mounted thermal cut out. An output limiter is fitted which allows the user to preset the maximum voltage available. •A heavy-duty power supply for powering laboratory experiments •Heavy duty variable transformer and high-power toroid transformer •Continuously variable output of 0 to 16 V AC and 0 to 20 V DC, capacitor smoothed •Output current 8 A. Output voltages are rated at 8 A load so higher voltages are available at less output current. •Manufactured in the UK with 5 years warranty •AC and DC outputs may be used simultaneously up to rated current. •Colour coded 4 mm sockets. •Maximum voltage limiter operated by Allen key •Push button cut-out to protect against overload and short circuit conditions •Mains Input 230 V, 50 Hz •Fusing: 5 A mains plug fuse

This repair kit for Irwin power supplies allows damaged plastic cases to be replaced quite easily. The kit comprises brand new plastic case in original Irwin blue, gloss black or crystal clear, three ""mushrooms"", which fit on the back of the case and act as cable tidy, new cable clamp and complete fitting instructions. In case of difficulties removing the old cable clamp and cable, specially designed tool to make the job easier is also available.

The Powerbase S5 is a great value power supply that provides a range of AC and DC voltages at 5A. Smoothing is achieved by a 4700uF capacitor. The supply has safe lockable DC and AC outputs ensuring the unit does not exceed the voltage required for experiments carried out by students. • AC & DC Output Voltages DC 3, 7, 10, 13, 17, 20 V - AC 3, 6, 8, 11, 13, 15 V • Current 5A • Supplied with and Allen key to lock minimum or maximum output • Voltage selector type - Stepped • Output type - Smooth non-regulated • Push button trip reset • Mains input 230/240V AC, 50Hz • Supplied with fused mains plug, lead and Allen key • Manufactured in the UK

The Powerbase S10 2-12 V AC/DC switched 5 A power supply unit is ideal for powering electrical experiments using the output voltages ranging from 2, 4, 6, 8, 10, 12 V AC and DC. Safe lockable DC and AC output this ensuring the unit does not exceed the voltage required for experiments carried out by students. • AC & DC Output: 2, 4, 6, 8, 10,12 voltage range in AC and DC • Current 5A • Supplied with Allen key to lock minimum or maximum output • Voltage selector type - Stepped • Output type - Full wave rectified, non-regulated • Push button trip reset • Mains input 230/240 V AC, 50 Hz • Supplied with mains plug and lead + Allen key • Manufactured in the UK

This Power Supply is suitable for wide variety of appliances which are powered by USB. UK mains plug with standard USB-A socket on top. V 2.1 DC output. • 5 V DC 2.1 (10.5 W) • RoHS compliant • CE marked

Spare Black Terminals for Satz School Power Stations.

Spare red terminals for Satz School Power Stations.

Car foot pump with 120 mm barrel and 450 mm hose with nylon connector and football inflator adapter. Complete with integral pressure gauge marked 0-100 p.s.i. and 0-7 kg/cm2 (7 bar).

The pump can be used to demonstrate the following: • Principle of siphon • Filtering using suction • Investigation of leaks in piping • Indirect transfer of liquid by means of negative pressure Please note this pump is not suitable for ""Bell in Jar"" experiments.

Javac V100 vacuum pump oil.

Rotary vane high vacuum pump, oil sealed and ideally suited for use in education. This unit is relatively quiet in use, can be operated for long periods of time, is robust, and is engineered for school use. The large oil capacity of 350 mL provides for long operation between oil changes. An oil level sight glass is incorporated so that the oil can be monitored. •Model: Javac CC-31ED •Air displacement: 40 L/minute •Ultimate vacuum: 25 micron 8 mm rubber hose fitting •Dimensions (L x W x H): 330 x 135 x 255 mm •Weight: 9.8 kg

Diaphragm pump suitable for vacuum or pressure work. Housed in a splashproof polycarbonate case. Please note this pump is not suitable for ""Bell in Jar"" experiments. 5 L/min flow rate 0.7 bar pressure 4 mm inlet/outlet Conforms to IEC1010

This robust Chemical Filtration Pump with PTFE diaphragm is a durable chemical resistant vacuum pump which is suitable for the following applications: vacuum filtration; desiccation; aspiration; degassing; other mid-range vacuum applications. It is ideal for both single funnel use and up to 6 holder manifold filtrations and suitable for organic and light acid/base (e.g. acetic acid solutions. The pump can also be used to pressurize up to 18 PSIG. Free air flow 31 l/min; Maximum vacuum 200 mbar. Please note this pump is not suitable for ""Bell in Jar"" experiments. Applications: • Filtration • Vacuum drying • Desiccators • Concentration • Suitable for basic and acid media Design Features: • PTFE wetted parts • Low noise emission • Direct drive • Continuous operation • No oil contamination • Low maintenance even in aggressive applications

Designed for general lab applications requiring only rough vacuum and moderate pressure. The pump is housed in tough, lightweight, plastic housing with an integral carrying handle and can be run continuously permitting use in applications such as filtering, drying, aerating and gas sampling. Easy to connect to apparatus via the hose connection on the side of the unit. Not recommended for organic, basic and acidic vapours. Vacuum to 292 mbar (219 Torr/21.3 in. Hg) and pressure to 2.3 bar (33 PSIG). Quiet, oil-free technology. Please note this pump is not suitable for ""Bell in Jar"" experiments.

Designed with microprocessor-controlled dual thermocouples, this stirring hot plate offers accurate temperature control and protection from overheating. The analogue models feature a coloured LED indicator which surrounds the heat control knob illuminating the actual surface temperature in real time. Powerful magnets and motor provide stirring speeds of up to 2000 rpm and mixing capability of up to 15 L of liquid. The square plate design allows flexibility of vessel sizes and combinations. Up to four 250 mL beakers can easily fit on the surface at the same time. To keep you safe, a “hot” warning light flashes whenever the plate surface temperature is above 50°C and continues to flash until the temperature drops below 50°C, even when unplugged. The unit includes BioCote antimicrobial protection which reduces the presence of odour and stain causing microbes such as bacteria, mould, and fungi on the product surface by up to 99.99%. Formulated from silver ion additives, BioCote provides built-in antimicrobial protection to support a more hygienic laboratory environment. This model includes an integral fitting for a retort rod and allows the retort base to slide underneath. Featuring a chemically resistant glass ceramic top plate that stays cool around the edges to help prevent burns. Please Note: BioCote® technology does not protect users or others against disease causing bacteria, germs, viruses, or other harmful organisms. This technology is not a substitute for good hygiene and/or cleaning practices.

Designed with microprocessor-controlled dual thermocouples, this stirring hot plate offers accurate temperature control and protection from overheating. The analogue models feature a coloured LED indicator which surrounds the heat control knob illuminating the actual surface temperature in real time. Powerful magnets and motor provide stirring speeds of up to 2000 rpm and mixing capability of up to 15 L of liquid. The square plate design allows flexibility of vessel sizes and combinations. Up to four 250 mL beakers can easily fit on the surface at the same time. To keep you safe, a “hot” warning light flashes whenever the plate surface temperature is above 50°C and continues to flash until the temperature drops below 50°C, even when unplugged. The unit includes BioCote antimicrobial protection which reduces the presence of odour and stain causing microbes such as bacteria, mould, and fungi on the product surface by up to 99.99%. Formulated from silver ion additives, BioCote provides built-in antimicrobial protection to support a more hygienic laboratory environment. This model includes an integral fitting for a retort rod and allows the retort base to slide underneath. Featuring a coated aluminium top plate for rapid heating and better temperature uniformity. Please Note: BioCote® technology does not protect users or others against disease causing bacteria, germs, viruses, or other harmful organisms. This technology is not a substitute for good hygiene and/or cleaning practices.

A cost effective hotplate/stirrer, the 'MS-Series has the following features and specification: • Case construction: Steel, with chemical resistant coating • Stage area: 180 x 180 mm • Temperature: Up to 400 °C (max) • Speed range: 100 - 1500 rpm • Power Supply: 220 AC

Designed with microprocessor-controlled dual thermocouples, this stirring hot plate offers you accurate temperature control and protection from over-heating. Actual surface temperature is displayed in real time on an easy-to-read digital screen. Powerful magnets and motor provide stirring speeds of up to 2000 rpm and mixing capability of up to 15 L of liquid. The square plate design allows flexibility of vessel sizes and combinations. Up to four 250 mL beakers can easily fit on the surface at the same time. To keep you safe, a “hot” warning light flashes whenever the plate surface temperature is above 50°C and continues to flash until the temperature drops below 50°C, even when unplugged. The units also include BioCote antimicrobial protection which reduces the presence of odour and stain causing microbes such as bacteria, mould, and fungi on the product surface by up to 99.99%. Formulated from silver ion additives, BioCote provides built-in antimicrobial protection to support a more hygienic laboratory environment. Includes an integral fitting for a retort rod and allows the retort base to slide underneath. Features a coated aluminium top plate for rapid heating and better temperature uniformity. Please Note: BioCote® technology does not protect users or others against disease causing bacteria, germs, viruses, or other harmful organisms. This technology is not a substitute for good hygiene and/or cleaning practices.

The SM5 mini stirrer is a powerful magnetic stirrer, capable of stirring up to 1 litre with an adjustable stirring speed up to 2,000 rpm. The unit is made from robust polypropylene with chemically resistant polycarbonate top. Features: • Lightweight stirrer • Capable of stirring up to 1 litre • Universal power adaptor • With BioCote antimicrobial protection • Dimensions (L x W x H): 143 x 143 x 64 mm

Constructed with powerful magnets and motor, this compact stirrer provides you with stirring speeds of up to 2000 rpm and mixing capability of up to 15 L of liquid. The square plate design allows flexibility of vessel sizes and combinations. Up to four 250 mL beakers can easily fit on the surface at the same time. For safety, this unit is designed to direct spills away from the user controls. The stirrer also features BioCote® antimicrobial protection which reduces the presence of odour and stain causing microbes such as bacteria, mould, and fungi on the product surface by up to 99.99%. Formulated from silver ion additives, BioCote provides built-in antimicrobial protection to support a more hygienic laboratory environment. Features a chemically resistant glass ceramic plate.

Constructed from chemically resistant ceramic coated steel, the MS-200 analogue magnetic stirrer delivers excellent reliability with reproducible results at a sensible price. A screwed 12.5 mm screwed thread is included for the addition of a retort rod (not included).

The HI-190M-0 is a compact and lightweight mini magnetic stirrer with plastic cover and can stir up to 1 litre. The compact size of this stirrer allows users to maximise bench space for efficiency and safety The internal Speedsafe™ mechanism ensures that the maximum speed of 1,000 rpm is never exceeded. The ABS housing will resist the most harmful chemicals in the classroom. Supplied with; •ABS cover •Micro stir bar •Instructions

An extremely good value compact magnetic stirrer, ideal for student use. The base is white to allow unaffected observation during experiments with colour indicators. The unit has adjustable feet to ensure stability on the bench. The speed is adjustable, and is controlled by the intuitive rotary knob on the front, which also controls power. Supplied with SELV (Safety Extra Low Voltage) AC adaptor, and magnetic stirrer bar.

An extremely good value compact magnetic stirrer, ideal for student use. The base is white to allow unaffected observation during experiments with colour indicators. The unit has adjustable feet to ensure stability on the bench. The speed is adjustable, and is controlled by the intuitive rotary knob on the front, which also controls power. Supplied with SELV (Safety Extra Low Voltage) AC adaptor, and magnetic stirrer bar.

Magnetic, encased in PTFE. With centre rim.

Magnetic, encased in PTFE. With centre rim.

Magnetic, encased in PTFE. With centre rim.

Magnetic, encased in PTFE. With centre rim.

Magnetic, PTFE coated stirring bar retriever. 35 cm in length.

This timer is most suited for an investigational approach for students to gain sound understanding of the concepts of time and motion. Two pairs of sockets alternately start and stop the timer, one pair operating in make mode, the other in break mode. The start/stop switches can be either mechanical or electronic. The timer is auto-ranging for ease of use and has clear 13mm digital display and has robust metal case with durable powder coat finish. An illuminated on/off switch is mounted on the rear panel adjacent to fused appliance inlet. • Electrical Supply: 220-240 V AC 50-60 Hz • Dimensions (W x L x H): 179 x190 x 85 mm • Mass: 1.6 kg • Ranges: 0 to 9.999s; 10 to 99.99s; 100 to 999.9s; 1000 to 9999s • Accuracy: ±0.01%

For use as a light operated timing gate. Comprises a photodetector and light source each housed in a robust ABS case spaced 40 mm apart on a plastic rod. Light source housing has a battery compartment and on/off switch. Photodetector housing is fitted with pair of 4 mm sockets to allow connection to electronic timers. When the timing gate is switched on it creates a short circuit between the two output sockets, this then becomes an open circuit each time the light beam is interrupted. Consequently the timing gate can be used as a remote switching device in wide range of dynamics experiments.

Replacement Cartridge for Deioniser, Vision 125

A compact all glass still, which can be wall or bench mounted. Produces up to 4 litres per hour of single distilled water. Consisting of horizontal boiler with 3 kW heating element and double coil condenser which cools the distillate to around 30 °C. The boiler can be drained via a stopclock and cleaned without dismantling. Two independent, automatic safety thermostats are fitted to prevent overheating. Supplied with level control device which turns the heater off when the reservoir is full. Requires minimum flow of1 l/minute. Dimensions 540 x 160 x 410 mm (W x D x H)

Spare boiler for the Distinction water still, WA17601.

Spare heater for the Distinction water still, WA17601.

An economically priced, wall mountable, all-glass water still, producing 4 litres per hour single distillate. With two independent safety thermostats, condenser, boiler, 3 kW sheathed heater and screw thread connections. Includes acid addition port and drain cock system for descaling the boiler. Dimensions 500 x 150 x 450 mm(W x D x H).

This water still produces ready-to-use cold, distilled water. The high quality borosilicate glassware coupled with silica sheathed heaters gives pyrogen-free distillate of the highest purity from virtually any raw water supply. The boiler feed is pre-heated to increase efficiency. The unique condenser design ensures that the droplets of distilled water remain in contact with the cooling coil for the longest possible time ensuring maximum energy transfer. All-glass construction allows rapid descaling using strong mineral acids. built- in ""clean"" function and integral acid addition funnel make the cleaning operation simple and safe with no need to dismantle any of the glassware. large bore stopcock with PTFE key is fitted for easy draining of chemicals after cleaning. A flow sensing device prevents overheating, and allows the unit to run on water supplies with pressure as low as psi (20 kPa). Requires a minimum flow of 1 litre per minute. There is an over-temperature thermostat mounted in the boiling chamber as an additional fail-safe. The acrylic safety screen and the cabinet lid are removable giving easy access to the glassware components. Screw threads are incorporated on all water connections so hoses can be fitted and removed easily and safely without risk of breakage. The control is simple and effective system which can be fitted to virtually any type of reservoir vessel. It will turn the still off when the reservoir is full, and restart it when the level in the reservoir drops, making it fully automatic. • 4 litres per hour output • Highly efficient • Fully automatic • Built-in ""clean"" function • Wall mounting bracket included

This battery has a 7 year shelf life and are suitable for high drain rate applications (although lithium cells may work better in some applications). It also has better low temperature performance than Zinc cells.

This battery has a 7 year shelf life and are suitable for high drain rate applications (although lithium cells may work better in some applications). It also has better low temperature performance than Zinc cells.

These batteries have 7 year shelf life and are suitable for high drain rate applications (although lithium cells may work better in some applications). They also have better low temperature performance than Zinc cells.

These batteries have 7 year shelf life and are suitable for high drain rate applications (although lithium cells may work better in some applications). They also have better low temperature performance than Zinc cells.

These batteries have 7 year shelf life and are suitable for high drain rate applications (although lithium cells may work better in some applications). They also have better low temperature performance than Zinc cells.

These batteries have 7 year shelf life and are suitable for high drain rate applications (although lithium cells may work better in some applications). They also have better low temperature performance than Zinc cells.

For watches, calculators etc.

For watches, calculators etc.

For watches, calculators etc.

For watches, calculators etc.

For watches, calculators etc.

For watches, calculators etc.

Packs of 5.

Battery Holder, AA Size.

Battery holder, 2 x AA batteries, with leads.

Battery Holder D Size. Pack of 5.

PP3 snaps with leads. Pack of 10.

Holds 4 x D (R20) batteries with outputs at 1.5, 3, 4.5 and 6 V. Batteries and leads not supplied. Each output has 4 mm socket.

Test the condition of your batteries using this low-cost, versatile and compact battery tester. The tester uses the power of the battery you are testing to power itself, so does not require batteries. • Suitable for checking the state of Zinc chloride, Alkaline and Rechargeable batteries • Will test AAA, AA, C, D, 9V PP3 and batteries

These low cost batteries have 2 year shelf life and are suitable for low drain applications.

These low cost batteries have 2 year shelf life and are suitable for low drain applications.

These low cost batteries have 2 year shelf life and are suitable for low drain applications.

These low cost batteries have 2 year shelf life and are suitable for low drain applications.

These low cost batteries have 2 year shelf life and are suitable for low drain applications.

These low cost batteries have 2 year shelf life and are suitable for low drain applications.

Apparatus for measuring rates of absorption or evolution of gases from organisms. Comprises two stoppered boiling tubes with wire baskets to support organisms. Each boiling tube is connected to simple manometer tube via three-way tap. The manometer tube is mounted on scale to measure the position and movement of the liquid level as gas is evolved or absorbed. The organism of interest is placed in the basket of one of the tubes, which also has some potassium hydroxide solution to absorb carbon dioxide. The other tube acts as thermobarometer, to counteract changes in temperature. Full instructions are included.

Spare Wire Baskets for BI180500

Explore the primary, secondary and tertiary structure of proteins with the captivating models and tools in this dynamic kit. This engaging, hands-on protein folding kit makes teaching protein structure basics easy. Students will fold a protein while exploring how the chemical properties of amino acids determine its final structure. Students can use the Amino Acid Starter Kit© to: •Learn that the 20 amino acids all share a common backbone but have different side chains, each with different chemical properties. •Identify the chemical properties of the side chains through a dual colouring scheme guided by the kit’s chemical properties circle, amino acid side chain list and coloured plastic clips. •Group the side chains into one of 5 categories: hydrophobic (nonpolar), hydrophilic (polar), negatively charged, positively charged, and cysteines, which sometimes form disulphide bonds. The coloured clip at the base of each side chain indicates chemical properties while embedded coloured balls in the amino acid side chain model show atomic structure. •Employ the kit’s protein-folding activities to first explore the primary and tertiary structure of proteins by constructing a generic 15-amino acid protein, then learn about the secondary structure of proteins by folding a toober model of the first of 3 zinc fingers of the Zif268 protein. Each 1-group set includes 1 chemical properties circle, 1 amino acid side chain chart, 22 amino acids, 1 mini toober, 22 coloured plastic clips and 6 hydrogen bond connectors.

These versatile modelling Toobers provide hands-on learning experiences in biology and chemistry. Students can model DNA or create protein structures and explore basic protein-folding principles. Toobers are flexible foam rods which have soft wire core that allows them to hold their shape well and they can be simply straightened out afterwards and re-used. Length: 120 cm long. Please note that theses are sold individually and the push pins are not included. See also 'Amino Acid Starter Kit' (MO110150). Also useful for teaching: • How hydrophilic/hydrophobic side-chains influence protein's structure • How structure is critical factor in many protein's function

This life size 2 part human brain is a median section model. The right hemisphere has the cerebellum and the stem with occipital lobe. On base. Numbered with English Key Card. Dimensions 190 x 150 x 150mm (D x W x H).

This 5-part classic brain model is an original anatomic cast of real human brain and comes divided along the midsagittal plane. The components of the brain's left half are: • Frontal and parietal lobe • Temporal and occipital lobe • Encephalic trunk • Cerebellum With integral magnets for easy viewing and hands on learning, the classic brain is great education tool for teaching and learning about the human nervous system and anatomy of the brain. The model comes complete with removable base for mounting and display purposes.

Students will immediately become engaged with this interactive foam model of double-stranded DNA and single-stranded RNA. The DNA Starter Kit© is schematic model that transforms from the familiar ladder shape to the double helix with twist. Students can explore the structure of colour-coded DNA bases showing purines and pyrimidines which connect to continuous sugar-phosphate backbone. Then they can delve into replication and transcription. Using individual nucleotide triphosphates, they can synthesize new strand of DNA one base at time showing the semi-conservative replication of DNA. Finally they can synthesize mRNA one base at time to show the process of transcription. Each kit includes: 51 bases (12 red adenine, 12 yellow thymine, 12 blue cytosine, 12 green guanine, 3 white uracil), 4 continuous grey backbones, 24 grey sugar-phosphates, 12 lavender sugar-phosphates and 48 orange phosphates.

The sky is the limit to what you can teach using these new large-scale, colour-coded foam nucleotides. Begin by teaching the complementary A-T and C-G base pairs and the antiparallel nature of double-stranded DNA. Move on to the flow of genetic information as you teach the basic processes of semiconservative DNA replication and mRNA transcription. You can then stretch students by introducing PCR (polymerase chain reaction) and the Sanger DNA sequencing method -- and much more. 80 Large-Scale Nucleotides: • 20 Red Adenosine • 20 Yellow Thymine • 20 Blue Cytosine • 20 Green Guanine 80 Adhesive-Backed Round Magnets

The model shows DNA and transcription of RNA. Height approx 500 mm. Complete with stand, instructions and model description.

Comprising abstract shaped colour coded parts to represent the nitrogenous bases, pentagonal sugar and pyramidal phosphate parts required to make the Double Helix model of DNA. The model can be displayed on its stand or untwisted into either flat or ladder form. The kits are designed so that only complimentary bases can be joined together. Scale 10 mm 2 Angstroms, 12 layer. The kit comes with stand and full instructions.

Comprising abstract shaped colour coded parts to represent the nitrogenous bases, pentagonal sugar and pyramidal phosphate parts required to make the Double Helix model of DNA. The model can be displayed on its stand or untwisted into either flat or ladder form. The kits are designed so that only complimentary bases can be joined together. Scale 10 mm 2 Angstroms, 22 layer. The kit comes with stand and full instructions.

Human ear, enlarged approx. 4 times and dissected into 5 parts, showing external, middle and internal portion. Ossicles and labyrinth can be taken out. Mounted on base, numbered and with Key Card. Dimensions 370 x 240 x 190mm (L x W x D).

Colourful representation of the outer, inner and middle ear including: removable eardrum with hammer and anvil, 2-part labyrinth with stirrup, cochlea and auditory/balance nerve. Comes with base and photocopiable key to parts in 4 languages.

Classic model of the human eye with highly accurate and detailed colourful components. Dissects into 6 parts: a two-part sclera with cornea and eye muscle attachments, both halves of the choroid with iris and retina, lens and vitreous humour. Comes with detachable base and photocopiable key to parts in 4 languages. Dimensions 205 x 130 x 150 mm.