TSL

Black plastic bracket for 2mm or 4mm dia. axles, can easily be drilled to larger sizes. Glue or screw to the chassis.

Medium Turned Birch wheels have a 4mm axle hole. One side is dished, the other flat. Tight fit on 5mm dowel.

Medium Density Fibreboard (MDF) wheels are 6mm thick with a 4mm nominal axle hole except D560-145 (75mm) which has a 5mm nominal axle hole.

5mm (3/16inch) dia. Pack of 100.

A pack of 80 cams in four different sizes, 4mm thick, which are a tight fit on 3mm rod. Extra holes enable them to be turned in to cranks. Supplied on the sprue, assorted colours.

Made from metal with 2 flywheels and 2 gears. With 3 fixing holes. Drive axle 105mm x 4mm.

High quality plastic propellers, tight fit onto a 2mm shaft (D560-204 fits 1mm ) 560-202 is a pusher propellor, the others are pullers. Packs of 10

The Sparmax ARISM Mini Kit includes: ARISM Mini Burgundy Red Compressor Sparmax MAX-4 Airbrush with 0.4mm nozzle and needle combination Sparmax Cleaning Pot with built in airbrush holder. The Sparmax ARISM Mini compressor embodies the philosophy of Sparmax: raising performance and rising above expectations through continuous improvement and unwavering quality. Reliable and functionally versatile, this innovative model exceeds the performance of similar sized compressors. The Sparmax ARISM Mini is a powerful and compact compressor; designed for workbench applications whilst saving the user space. As a smaller unit, it was also designed to be highly portable, for use on-the-go and easy to store. In keeping with it's compact nature, the Sparmax ARISM Mini also has a built-in airbrush holder on it's handle. This is the quintessential compact compressor for all ages and experience levels, and is available in 8 color options. Sparmax ARISM Mini Compressor (Cosmic Grey) The Sparmax ARISM Mini compressor features: Low maintenance, oil-less single piston air compressor Working pressure from 0 psi to 28 psi Manual on/off switch 2M Braided hose Pressure Adjuster Handle with built in airbrush holder Air flow: 12 - 14 lpm (0.42 - 0.49 cfm) at open flow 1/8 BSP outlet on compressor Size: L17.5 x W9 x H18.2 cm (5.6"""" x 3.5"""" x 6.6"""") Weight: 2.5 kgs (5.5 lbs) Voltage: 220-240V 50Hz Noise level: 49±dB Duty cycle: 30 minutes continuous use. After 30 minutes of continuous operation, use the On/Off Switch to turn off the unit. Allow the unit to cool for 10 - 15 minutes before turning the compressor back on. Airbrush: The Sparmax MAX-4 airbrush provides exceptional performance with even the smallest compressors because it atomises well at low pressures. It has a 0.4mm needle and nozzle combination for general purpose, high paint flow spraying and wider spray patterns. The 0.4mm nozzle is ideal when spraying thicker or heavier paints whilst still obtaining a fine level of detail. The Sparmax MAX-4 is a dual-action airbrush but can be easily converted to a Single-action airbrush with the Single-action Air Valve that is included. It also features a Pre-set Handle which limits the colour flow to avoid over-shooting and a Crown Cap allowing you to get closer to your work and thus achieve finer detail, whilst still protecting the needle. The Sparmax MAX-4 airbrush features: Gravity-feed with 1/4 oz (7ml) fixed cup with lid Dual-action airbrush with Single-action valve included Ð converts the airbrush from a dual-action to a single-action airbrush (simple installation guide included) Internal-mix 0.4mm needle and nozzle combination for high performance, general purpose, high paint flow spraying and wider spray patterns 0.4mm nozzle suitable for thicker or heavier paints Fine detail to 1"""" (0.4mm to 25mm) spray pattern with the one size nozzle Ergonomic handle design with a Pre-set colour flow control Extra Crown Cap included Cleaning brush included Replaceable internal PTFE solvent-proof needle packing for use with solvent-based paints 2 Year Warranty ""

Mobile three tier storage on heavy duty castors with two front locking. Provides 72 spaces on three levels.

Reel of 100m black waxed thonging

Medium Turned Birch wheels have a 4mm axle hole. One side is dished, the other flat. Tight fit on 5mm dowel.

This economical rack has 24 x 50mm spaces for A2 or A3 folders on each shelf. Two or three tier models are available as static OR mobile with feet or castors - customer to specify. (HxWxD) 1950 x 1500 x 580mm.

Black wheels and tyres moulded in PVC. Small sizes are car type, the larger are tractor/lorry type.

Solid birch turned balls. Packs of 10.

These set squares are made from clear tinted plastic with bevelled edges. Staedtler set squares are graduated in mm on one side and figured every 10mm in cms.

These set squares are made from clear tinted plastic with bevelled edges. Staedtler set squares are graduated in mm on one side and figured every 10mm in cms.

Supplied in a plastic wallet with a spare lead. It has a fixed point friction head compass for circles from about 3 to 340mm dia. Height: 128mm.

Semi-circular and full circle protractors made from polystyrene with bevelled edge and 1° graduations.

A3 drawing board carry case made from 3mm corriflute with carrying handle and case clips. Dimensions: 510 x 390 x 50mm. This carry case is suitable for 580-604 only. Case supplied flat packed for easy assembly.

Designed to store Walton A2 and A3 size drawing boards. The large size will store 20 Harlestons or 30 Starstons. Smaller size will store 10 Harlestons or 15 Starstons. Lock fitted as standard. Dimensions: 1202mm W x 418mm D x 840mm H

Erasers for the removal of lead from paper and film.

Cotton base, white, approx. 125g reel.

These polypropylene wheels are 50mm wide, with 4mm axle hole. in a pack of 100 wheels. Individual bags contain one colour.

Modern design of compass featuring large easy grip bow-top, self-centring mechanism and unique safety point. 3 colour assortment. Pack of 25.

These set squares are made from clear tinted plastic with bevelled edges. Staedtler set squares are graduated in mm on one side and figured every 10mm in cms.

British made 4mm stackable plugs. A 4mm socket is incorporated in the rear for in line stacking. Screw connection for wire. Rated 10A.

LED CLIPS Packs of 10 - 5mm clip single part.

Standard commercial quality 12 way terminal blocks. Polythene construction, easily subdivided, rated 380 V rms.

British made 4mm stackable plugs. A 4mm socket is incorporated in the rear for in line stacking. Screw connection for wire. Rated 10A.

Suitable for normal industrial and professional applications. Base laminate conforms to all international standards and releases, as lisited in IPC4101A. RoHS compliant. Specifications Thickness:1.6mm Copper foil:35 micron Dissipation factor:35 Dielectric constant:5.4 Solderbath resistance (260°C): 20 secs Resist thickness:5 microns Spectral response:350-450nm, typical 2-3 minute exposure UV light energy required:Approx. 50mJ/cm Shelf life:1 year at 15-20°C

Suitable for normal industrial and professional applications. Base laminate conforms to all international standards and releases, as lisited in IPC4101A. RoHS compliant. Specifications Thickness:1.6mm Copper foil:35 micron Dissipation factor:35 Dielectric constant:5.4 Solderbath resistance (260°C): 20 secs Resist thickness:5 microns Spectral response:350-450nm, typical 2-3 minute exposure UV light energy required:Approx. 50mJ/cm Shelf life:1 year at 15-20°C

Suitable for normal industrial and professional applications. Base laminate conforms to all international standards and releases, as lisited in IPC4101A. RoHS compliant. Specifications Thickness:1.6mm Copper foil:35 micron Dissipation factor:35 Dielectric constant:5.4 Solderbath resistance (260°C): 20 secs Resist thickness:5 microns Spectral response:350-450nm, typical 2-3 minute exposure UV light energy required:Approx. 50mJ/cm Shelf life:1 year at 15-20°C

With solder connection.

BS 1363. Fused, insulated pins.

Non-rechargeable Alkaline batteries, which have up to 6 times the energy content of standard zinc-carbon batteries. Leak resistant, 100% mercury free. RoHS exempt.

With solder connection.

The Professional breadboard has contact positions identified by alphanumeric grids. The Professional also have colour coded polarity indicators. Size: 80 x 54mm with 400 tie points. Contact life: over 10,000 insertions.

Panel mounting SPST 10 amp 250V AC. panel cutout 19.3 x 13mm Terminals 4.8 x 0.8 crimp (D250-694)

Overload protection on all ranges except 10A DC current rnge. Low battery indication. Robust ABS housing, with protective yellow rubberised holster. A low cost multi-function instrument which offers excellent value for educational use. Supplied complete with safety test leads, battery and instructions. Designed in accordance with IEC1010 600V Cat II. CE approved Range 200mV 0.1mV 0.5% + 5 250V rms 2V 1mV 0.8% + 5 600V DC/AC rms 20V 10mV 0.8% + 5 200V 100mV 0.8% + 5 200mV 0.1mV 0.5% + 5 250V rms 2V 1mV 0.8% + 5 600V DC/AC rms 20V 10mV 0.8% + 5 200V 100mV 0.8% + 5 AC Volts: 200V 100mV 1.2% + 10 600V 1V 1.2% + 10 Transistor: Test current 10uA. Vcc 3.0V. hFE 1-1000 Diode: Test current 1mA approx. Voltage 2.8V approx. Continuity: Buzzer sounds when resistance <50W approx. Dimensions: 126x70x28mm. Weight 155g approx.

Panel mounting with solder tag terminals. Supplied with On-Off indicator plate.

DPDT slide switch 22 x 13 x 12mm.

With wire leads.

Single pole push-on/off press switch with screw terminal connections. Specifications: Rating: 2A @ 250VAC Panel cutout: 10mm. Max panel thickness: 3mm

With snap connectors.

With wire leads (wl).

They have snap connectors that accept PP3 battery snaps except D250-527 and 528 which have solder tags (st), and D250-526, 535 & 746 which have wire leads (wl).

11mm Round - 1.5 V 200mA

(4 Amps RMS, plastic case type TO126)

Battery Snaps have colour coded 150mm long insulated leads. Pp3 snaps fit PP3 batteries and the battery holders above. *Moulded UL & CSA approved.

White plastic screw connections 30mm dia 19mm high.

Miniature circular DC motor, ideal for models and educational applications.Nominal voltage 3.0V with operating range 1.5 to 4.5V. The two flat sides enable easy mounting onto a panel or PCB. Rotation is counter-clockwise (as viewed from shaft end). Nominal voltage: 3.0V Operating range: 1.5-4.5V No load speed: 16000 RPM No load current: 0.4A Speed at max. efficiency: 12400 RPM Current at max. efficiency:1.5A Torque: 11.9g-cm Dimensions: L: 25 (exc. shaft) W:20.1 H:15.1mm. Shaft length 8.1x 2.0 dia. Weight 19g approx.

Medium torque DC motor with operating range 1.5 to 4.5V, ideal for educational and modelling applications. Rotation is clockwise as viewed from shaft end. Dimensions: L: 27 (exc. shaft) x 24mm dia. Shaft length 8.6x 2.0 dia. Weight 28g approx. Nominal voltage: 3.0V Operating range: 1.5-4.5V No load speed: 6600 RPM ±10% No load current: 0.13A Speed at max. efficiency: 5100 RPM Current at max. efficiency: 0.4A Output: 0.42W Torque: 11.6g-cm Stall torque: 55g-cm min. Stall current: 1.4A max.

25mm O.D. Self adhesive pad on base.

These solar motors are low inertia types with low current drain suitable for use with solar modules & cells shown above. They can also be used instead of standard motors to reduce battery current drain.

This mono amplifier kit uses an LM386 audio amplifier IC which can output 1.25W of power. The kit is supplied with a pre-built jack cable and a PP3 battery clip, and can run off any voltage from 4 to 12 Volts (Absolute Maximum 15V). Requires a PP3 (9V) battery.

This stereo audio amplifier kit is an ideal basis for a design and technology project, and works with any personal stereo equipment. It uses a NJM2073D audio amplifier IC which can output 1W per channel. The kit is supplied with two speakers and a pre-made 3.5mm jack plug. It works nicely off a PP3 battery (9V), or runs off any voltage from 2 to 15 volt. NOTE - this kit needs to be assembled

A high torque miniature DC motor with an operating range of 1.5V to 6.0V, suitable for educational and modelling applications. Rotation is clockwise as viewed from shaft end. Dimensions: L: 30.5 (exc. shaft) x 24mm dia. Shaft length 10mm x 2.0mm dia. Weight 42g approx. RoHS compliant Nominal voltage: 3.0V Operating range: 1.5-6.0V No load speed: 9600 RPM ±10% No load current: 0.25A Speed at max. efficiency: 7790 RPM Current at max. efficiency: 1.14A Output: 1.58W Torque: 19.9g-cm Stall torque: 110g-cm min. Stall current: 5.2A max.

Miniature circular DC motor. Rotation is clockwise (as viewed from shaft end). Dimensions: L: 25 (exc. shaft) x 21mm dia. Shaft length 8.1x 2.0 dia. Weight 19g approx. RoHS compliant Nominal voltage: 3.0V Operating range: 1.5-3.0V No load speed: 14700 RPM No load current: 0.3A Speed at max. efficiency: 11524 RPM Current at max. efficiency:1.05A Torque: 14.1g-cm Stall torque: 65g-cm Output: 1.65W

High-quality nickel-plated steel split rings. Packs of 100.

Supplied with black hour/minute hands (950-395) & red second hands (950-396). Spindle length: 12mm. Pack of 10.

High-quality nickel-plated steel split rings. Packs of 100.

AA size battery boxes moulded in black ABS with detachable lids, and available with or without miniature on-off slide switch. Connection via flexible red & black wire leads (150mm approx). The lids may also be secured by the small screw provided. Dimensions (mm) L x W x H 2 x AA Size 68 x 35 x 19 3 x AA Size 68 x 48 x 19 4 x AA Size 68 x 65 x 19

Moulded in black ABS with detachable lids, with miniature on-off slide switch. Connection via flexible red & black wire leads (150mm approx). The lids may also be secured by the small screw provided. Dimensions (mm) L x W x H 3 x AA Size 68 x 48 x 19

Supplied with black hour/minute hands (950-395) & red second hands (950-396). Spindle length: 12mm. Pack of 10.

This stereo audio amplifier kit is pre built. It's ideal for product design projects. It uses a NJM2073D audio amplifier IC which can output 1W per channel. The kit is supplied with two speakers and a pre-made 3.5mm jack plug. It works nicely off a PP3 battery (9V), or runs off any voltage from 2 to 15 volt. All that is required is to solder the jack lead, speaker & power clip to the board.

This kit allows you to build an economic mains powered lamp that takes power from a standard 5V micro USB phone charger (not included). The kit comprises a very bright 1W Power LED which connects (with the cable provided) to a PCB that has a power switch, micro USB connector and power resistor. All that is required to assemble the kit is to connect the LED to the desired length of cable and solder the resistor to the board.

DPDT 15 x 8 x 7mm.

Take power from a PC with this handy USB lead. The lead is 1m long and has pre tinned red and black wires which connect to the 5V pins on the USB plug. The USB standard allows peripherals to draw 100mA each, which is enough to power an LED or most simple circuits.

Battery Snaps have colour coded 150mm long insulated leads. Pp3 snaps fit PP3 batteries and the battery holders above.

With a positive working photo-resist coating, protected by a peel-off plastic film. Suitable for normal industrial and professional applications. Base laminate conforms to all international standards and releases, as lisited in IPC4101A. RoHS compliant. Specifications Thickness:1.6mm Copper foil:35 micron Dissipation factor:35 Dielectric constant:5.4 Solderbath resistance (260°C): 20 secs Resist thickness:5 microns Spectral response:350-450nm, typical 2-3 minute exposure UV light energy required:Approx. 50mJ/cm Shelf life:1 year at 15-20°C

MULtI strAND - Flexible Rated: 1.4A @ 1000V RMS max. 7 cores x 0.2mm. 100 metre reel

The FM radio kit offers fantastic reception quality and outputs 1W of power. It uses industrial surface mount ICs which are mounted on the board. You just have to solder the remaining resistors, capacitors and other components to finish the kit. The radio has controls for tuning and to adjust the volume. The circuit includes an audio amplifier and output is via a 66mm diameter speaker. The board can be powered from a 2.5V to 5.5V supply and works nicely off a 5V wall supply or 3x AA batteries. An optional FM radio telescopic aerial is also available.

The BC548B and BC639 are low cost alternatives to the BC108 and BFY51/2N3053 respectively. They match specification of the originalsalmost exactly. The pinouts are different but they can be made to fit existing circuits by bending the legs.

High quality LED's for PCB or panel mounting. Standard brightness.

High luminous output, Red/Pure Green/Blue flashing LEDs. White diffused and water clear types available.

DPCO has a centre off position.

A photoconductive cadmium sulphide LDR housed in TO-18 package 4.5mm dia. Cell resistance 20KW at 10 lux, 5KW at 100 lux. Dark resistance minimum 20MW Max dissipation 50mW, maximum voltage 100V dc.

Build a computer desk lamp or ornament using this simple board. The board takes power from a USB port and the light can be turned on/off with the on board switch.

Money saving bulk pack containing 10 sheets of 1000 x 600 x 3mm opaque cast acrylic. Pack contains two each of Blue, Red, Green, Yellow and one each of Black and White. Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Money saving bulk pack containing one each of electric blue, sapphire blue, emerald green, glacier green, chilli red, blush pink, mandarin orange, citrus yellow, clear & polar Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Money saving bulk pack containing two each of opaque red, blue, yellow, green and one each of black and white. Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Money saving bulk pack containing two each of red, blue, clear and 1 each of yellow, green, white, black. Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

GEF eco friendly vinyl is PVC free which means no chlorine gases are released when burnt making it safe for use on a laser cutter. Self adhesive and great for all kinds of indoor and outdoor applications with outdoor durability up to 5 years. 610mm wide 10m roll. sticky back/self adhesive

GEF eco friendly vinyl is PVC free which means no chlorine gases are released when burnt making it safe for use on a laser cutter. Self adhesive and great for all kinds of indoor and outdoor applications with outdoor durability up to 5 years. 610mm wide 10m roll. sticky back/self adhesive

70mm length, 30mm each side, with 30mm angle.

Clear plastic suckers will allow rigid materials to be stuck to glass. A hole is drilled through the material and the end of the sucker is pushed through. Size 21mm.

Money saving bulk pack containing two each of crystal clear, polar frost and one each of electric blue, sapphire blue, emerald green, glacier green, chilli red, blush pink, mandarin orange & citrus yellow Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.