TSL

The TSUB may also be used for other similar applications including portable benches and small individual machines. The TSUB has exceptionally low noise characteristics for use within the classroom and is designed for use with fi ne dusts. Warm air is returned to the classroom being sympathetic to environmental issues. A complete installation service is available by our engineers. Inlet sizes: 1 x 80mm & 1 x 63mm diameter ports, one either side OR 2 x 63mm diameter ports, one either side. Please specify inlet port diameters and locations (LHS/RHS) at time of order placement. These products require specialist installation & training. Please contact us for further information.

The TSFL has exceptionally low noise characteristics for use within the classroom and is designed for use with fine dusts. Warm air is returned to the classroom being sympathetic to environmental issues. The Top Extraction Kit is available for installation by our engineers. Inlet sizes (left and/or right side: 1 x 100mm & 1 x 80mm diameter ports OR 2 x 80mm diameter ports OR 1 x 120mm port on one side only. Please specify inlet port diameters and saw model number at time of order placement. These products require specialist installation & training. Please contact us for further information. Airflow: Approx. 600m3/hr at 1000 pascals.

This disc will not cut fingers even if touched accidentally. With the Tungsten Carbide Flange Cutter (an optional extra) it will cut out the moulding with a 5mm flange around its perimeter. The cutting edge of this cutter is well protected from contact with the user and full instructions are supplied. No volt release switch fitted as standard. Key Features • 400 x 455mm table top • Multi tool arbor • Tungsten carbide abrasive disc and holder • Tool height adjustment facility • Upgradeable to the 2020

The standard tilting table is 226 x 278mm and indexed 135-90°. The bench machine has dust extraction takeoff points and requires a non-latching footswitch (530-795). KEY FEATURES • Bench mounted • Quick action calibrated tilting table for operating positions between 90° and 135° • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 15mm x 1090mm aluminium oxide abrasive belt

It has a large cast iron tilting fence for accuracy and timber support, front and rear cutterblock guards, shaw guards for rebating and features an enclosed drive mechanism. A no-volt release starter with thermal overload, key switch, footswitch and anti-kick back fingers for thicknesser are fitted as standard. KEY FEATURES • Two Knife Cutter block • Cast Iron table • Cast Iron fence • 180 x 255mm thicknessing capacity • 255mm surfacing width • Footstop and key switch included • UK Manufactured

The two fences can be used together with the Tungsten Carbide Disc to cut out slots and rebates in wood. Full instructions are supplied. No volt safety switch fitted as standard. Key Features: • 400 x 455mm table top • Multi tool arbor • Tool height adjustment facility • Adjustable 0 to 10 tilting table • Adjustable guide and extraction fences • Large dia. Hand wheel for tool height adjustment • Full toolkit including tungsten carbide abrasive disc, flange cutter, mini mops & compound bars and mini flapwheels

The bench mounted machines incorporate adjustable dust collection hoppers for use with a centralised dust extraction system. Set of polishing mops included.

The standard tilting table is 226 x 278mm and indexed 135-90°. The bench machine has dust extraction takeoff points and requires a non-latching footswitch (530-795). KEY FEATURES • Bench mounted • Quick action calibrated tilting table for operating positions between 90° and 135° • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 15mm x 1090mm aluminium oxide abrasive belt

The standard tilting table is 226 x 278mm and indexed 135-90°. The integral dust extraction system significantly improves performance and combined with cassette collection and disposal enhances easy, convenient waste handling. Fully compliant with UK COSHH regulations, the European Machinery Directive and also with the BS4163:2014 Health and Safety in Workshops of Schools and Similar Establishments” Regulations. Supplied and fitted with a medium grade, grit belt. KEY FEATURES • Dust extraction mounted • Quick action calibrated tilting table for operating positions between 90 and 135 degrees • Adjustable protractor guide • Thumb screws for belt adjustment • Supplied with 150 x 1090mm aluminium oxide abrasive belt

250mm dia blade for MACC-TE250.

With a cast iron table at the heart of this compact machine it is designed to offer those with limited space or budgets a real bandsaw with sensible capacity and performance, as an alternative to lightweight hobby machines. It shares the same essential build qualities as its larger cousins, strong steel frames, dynamically balanced bandwheels, cast iron tables and an induction motor. It has been designed to offer the user with space restrictions a serious machine in compact form. Key Features: • Blade Guides - Simple to set and easily adjustable • Sealed for life bearings - Require no maintenance during the life of your machine • Capacity - Large 120 mm depth of cut and 240 mm throat depth make this a compact machine capable of serious work • Strong Fence - With cam action lock for ease of use and simple tension adjustment for clamping strength (clamps at rear of table) • Table - A solid, finely ground cast iron table provides an ideal and low friction work support • Trunnion - Table tilts from 0 - 45º on a solid trunnion with easy to read scale Specification: Maximum Depth of Cut: 120mm Throat Depth: 240mm Table Size: 315 x 350 mm Table Height from Floor: 370 mm Motor Power: 1/2 hp Blade Length: 70 1/2"" Blade Width Capacity: 1/4 - 1/2"" Blade Speed: 740 M / minute Extraction Port Diameter: 58 mm (100 mm with supplied adaptor) Height: 860mm Width: 550mm Depth: 480mm Weight: 30kg

Features: • Movable Head 45° right & left • Reduction unit in oil bath • Membrane pump for coolant • Coolant filter • Vice complete with anti-burr device • Bar stop • 24 Volts low voltage installation with hold-to-run head control knob • Service tools • Instruction manual & spare parts

Pedestal for MACC-TE250

Image shows dust extraction unit incorporated into machine bench.

Programmable spindle speeds and feedrates make the VMC 1300 ideal for cutting a range of resistant materials such as wax, plastic, acrylic, free cutting alloys, aluminium and steel. Also available for integration into FMS/CIM systems (additional equipment must be fitted at the time of manufacture. The VMC 1300 comes as standard with: • VR CNC Milling Operating Software (PC not included) • Installation and instruction manuals • Power Drawbar with manual actuation • Workholding clamps • USB connection

The machine can be supplied for left or right handed operation and for a small surcharge it can be supplied with the necessary parts for easy conversion in the workshop. TECHNICAL DATA • Drilling capacity in mild steel 13mm • Motor 0.25kW Single phase • Throat depth 194mm • Speed range 500-4000rpm • No. of speeds 5 • Table size 235 x 409mm • Dimensions 815 x 372 x 627mm • Weight 46Kg KEY FEATURES • Made in the UK • Bench mounted • Easy to use • Front mounted controls • Head raising mechanism

The machine can be supplied for left or right handed operation and for a small surcharge it can be supplied with the necessary parts for easy conversion in the workshop. TECHNICAL DATA • Drilling capacity in mild steel 13mm • Motor 0.25kW Single phase • Throat depth 194mm • Speed range 500-4000rpm • No. of speeds 5 • Table size 235 x 409mm • Dimensions 815 x 372 x 627mm KEY FEATURES • Made in the UK • Bench mounted • Easy to use • Front mounted controls • Head raising mechanism • Latching footswitch

The TSFLA has exceptionally low noise characteristics for use within the classroom and is designed for use with fine dusts. Warm air is returned to the classroom being sympathetic to environmental issues. A certified explosion vent relief panel is supplied to meet local authority or HSE requirements. The Top Extraction Kit is available from Technology Supplies for installation by our engineers. Please specify inlet port diameters and saw model number at time of order placement. These products require specialist installation & training. Please contact us for further information.

The TSHS has a primary dust separator in the form of a cyclone, which removes the bulk of the extracted dust, leaving relatively clean air to pass through a secondary cartridge fi lter, thus extending fi lter life. The TSHS has exceptionally low noise characteristics for use within the classroom and is designed for use with fi ne dusts. Warm air is returned to the classroom being sympathetic to environmental issues. A complete installation service is available from our engineers. These products require specialist installation & training. Please contact us for further information.

The TSPL may also be used for other similar applications and offers the designer a realisticn alternative to a Centralised Ducted System. The TSPL has exceptionally low noise characteristics for use within the classroom and is designed for use with coarse dusts, hence the large collection bin capacity and the comparatively low footprint area of the machine. Warm air is returned to the classroom being sympathetic to environmental issues. A cerfified explosion vent relief panel is supplied if required to meet local authority or HSE requirements. Extraction Kits for Planers and Wood Lathes are available from Technology Supplies for installation by our engineers. Please specify inlet port diameters, locations (LHS/RHS) and lathe/planer model at time of order placement. These products require specialist installation & training. Please contact us for further information.

Mobile stand on heavy duty lockable castors.

Ni-Chrome wire 20swg x 10m for sculpture tool & Models 600 1000 hot wire Strip Heaters.

The key to quality is good preparation. It can make the difference between a success and failure. Why? Because poorly heated materials does not perform as well, increasing your costs if you have to start again. The C R Clarke 200FD is designed by plastic forming experts. Digital controls mean precise heating. And the mix of a circulated fan and insulation maintains consistent heat. The result. Material which work ready, so your students can get straight on with their projects. Ideal for heating materials for dip coating, dome blowing, press forming and thermoforming. Key features: • Internal capacity 508 x 355 x 304mm • Heats up to 350°C - Perfect for thermoforming plastics and pre-heating • Digital control - Achieve the ideal temperature for processing • High quality, asbestos-free ceramic fibre wool insulation - A consistent temperature means better quality and less waste • Single phase - Plug in any socket or hard wire to a switched outlet • No volt release and overload protection - Keeping safety in the classroom paramount

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

Compact and affordable. C R Clarke 1210 vacuum former is an ideal entry level machine. Its smaller forming area means lower cost for materials. Perfect for first time users and simple model making. 240V, single phase. Key features: • 4 independent ceramic heaters - Balance out temperature variations across four zones • Interlocked guard - Moving parts are safely contained while allowing good visibility of the forming process • Blow release - Remove parts from mould without effort • No-volt safety switch - Automatically isolates machine in the event of power failure Included items: • C R Clarke 1210 vacuum former machine • Starter pack of material

Turn your C R Clarke 1210 vacuum former into a mobile workstation. Sturdy, easy to move, and features a storage shelf to keep all accessories to hand. Ideal for small departments where worktop space is limited.

This machine is a perfect mid-range vacuum former, ideal for schools and model makers. It has a smaller forming area than the C R Clarke 750FLB, and is desktop mountable. 240V, single phase. Key features: • Independent ceramic heaters - Balance out temperature variations across four zones • Interlocked guard - Moving parts are safely contained while allowing good visibility of the forming process • Digital timer with alarm - Monitor the cycle more efficiently • Blow release - Remove parts from mould without effort • No-volt safety switch - Automatically isolates machine in the event of power failure * Reducing frame available - Decrease the forming aperture Included items • C R Clarke 725FBL vacuum former machine • Starter pack of material

Reduces the standard forming area of the C R Clarke 725 and 917 vacuum formers from 228 x 432mm to 228 x 216mm.

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

Turn your C R Clarke 725 vacuum formers into a mobile workstation. Sturdy, easy to move, and features a storage shelf to keep all accessories to hand. Ideal for small departments where worktop space is limited.

This range of strip heaters will handle most common thermoplastics. It operates using multiple low voltage hot wires. The heating wires produce an accurate and controllable line of heat to give sharp bends. The hinged top section incorporates cut-off switching to turn the heating wires off while loading and unloading.

The 320 Dome Blowing Unit consists of a rigid base with a heat-proof seal plate that has perforations to allow air to be injected. A sheet of thermoplastic material, normally cast acrylic, is heated in an oven to its softening temperature. The material is transferred to the Dome Blowing Unit and is clamped into position. Air is blown under the sheet using the control valve on the front panel, inflating the dome. An adjustable height gauge assists the user to achieve consistent dome heights. Once cooled, the dome is unclamped and is immediately ready to use. The 320 requires an external air supply, this can come from a compressed air supply or the Pressure Outlet of one of our Vacuum Forming Machines. The 320 is supplied with rings to make domes of 300, 225 and 150mm in diameter.

It uses a 125 watt motor and router bit combination mounted in a unit measuring 355 x 380 x 380mm. The combined fence and guard protects the user from the cutter and enables fine detail to be trimmed safely. It will trim right up to an edge or leave a flange as desired. Single phase industrial motor. Swarf collection duct. Angled work support table. Foot switch operated for safety. Supplied with 3mm dia. slot drill.

The 280 has a fine heating wire capable of cutting expanded polystyrene materials up to 250mm in thickness. Variable power to the wire is supplied from the low voltage transformer housed in the base of the machine. Freehand shapes can be cut with ease, while the machine table also has grooves to accept the accessories supplied with each machine: • Parallel Guide • Protractor Guide for non-parallel cuts • Circle Cutter

Fluidised baths consist of a tank to hold thermoplastic powder, a plenum box and a porous membrane. When low pressure high volume air is blown through the powder via the plenum box it causes the powder to lift and disperse thus behaving like a liquid and permits immersion of a preheated metal component. • Everything needed to carry out dip coating with plastic powders • Contains: Model 300 and 150 fluidised bath, Model 120 blower unit and stand • 670 x 700 x 770mm

A kit of parts for replacing the silicone seals etc on popular vacuum formers. If your machine is not performing well, the filter may also need replacing. Includes silicone seal, platen seal filter element & adhesive

Jacobs No.6 internal taper and K3 key.

For Craft & Supercraft chucks, 13mm & 16mm.

For processing wider boards on the Sedwick TA315 Circular Sawbench.

It has a large cast iron tilting fence for accuracy and timber support, front and rear cutterblock guards, shaw guards for rebating and features an enclosed drive mechanism. A no-volt release starter with thermal overload, key switch, footswitch and anti-kick back fingers for thicknesser are fitted as standard. KEY FEATURES • Two Knife Cutter block • Cast Iron table • Cast Iron fence • 180 x 255mm thicknessing capacity • 255mm surfacing width • Footstop and key switch included • UK Manufactured

Whether deep ripping or cutting the most intricate shapes, the design features of this machine ensure it is done precisely and effortlessly. • Two speeds 800 and 1200 m/min for the most varying materials • Sturdy cast-iron table tiltable from -20° to +47° • 3-roller precision guiding above and below the table • Upper saw blade guiding by toothed rack, adjustable in its height • Balanced and polished band wheels with rubber facing • Quick-clamping lever for saw blade • Maximum cutting height: 300 mm • Throat 440 mm • Precision rip fence with magnified scale which can be set both left and right of saw blade • 3phase HxWxD: 1930 x 800 x 1140mm Weight: 214kg

The rip fence is aluminium section allowing for two working positions (ripping and angled ripping). It is fixed to a cast iron mounting bracket for rigidity and has integral micro adjustment. A telescopic extension arm is fitted to the cross cut fence for setting the timber stop. The 620mm Cross Cut Table is designed for cutting mitres and compound angles, end trimming, squaring, dividing and trimming. It has a maximum depth of cut 105mm @ 90° and 76mm @ 45°, double sided saw guard with dust extraction outlet, enclosed drive mechanism. Supplied with an anti kick saw blade. Thermal overload, no-volt release switch, lock off emergency stop switch and foot operated foot switch are fitted as standard. Fitted with keyswitch.

This machine features a temperature controlled heating barrel, rack and pinion injection ram, over centre mould closing, automatic moulding ejection and is supplied with a wheel mould (flat upper & shaped lower mould) and 2kgs of red polystyrene granules. To operate the machine, plastic granules are loaded into the heating barrel. After a short pre-heat time, the plastic is ready to inject. The mould is closed and the injection ram lowered. This action automatically opens a valve in the injection nozzle and the plastic is injected. Once the mould is full the ram is retracted. The heating barrel rises on its return springs, closing the valve. After cooling the mould is opened and the moulding is ejected by pins in the mould cavity. Requires permanent fixing or bolting down. Safe and easy to use.

The 180 combines a heated wire on a tensioned bow, ideal for cutting expanded polystyrene models, with a horizontal wire or strip heating of rigid plastic materials. This compact unit is ideal for smaller workshops.

Service kit for replacing silicon seal on the CR Clarke 1210 Vacuum Former. Service kit includes: silicone seal, platen seal, adhesive, and primer. NOTE: If your machine is not performing well, the filter may also need replacing.

A kit of parts for replacing the silicone seals etc on popular vacuum formers. If your machine is not performing well, the filter may also need replacing.

This folding jig from C R Clarke is a useful accessory to their range of strip heaters. The jig has a working length of 600mm and is adjustable from 160° obtuse to 30° acute. The jig's calibrated protractors ensure consistent setting, with hand knobs for easy adjustment. The adjustable work stops can also be used to hold the material in the folding jig, allowing the operator to continue with other work while the folded material cools.

Expert II Series is an excellent choice for beginners and provides optimum speed, superior quality, solid reliability and unmatched value. Expert II produces eye-catching graphics with up to 27.8 ips cutting speed, 350g of cutting force and 3 metres (9.84 feet) of tracking ability. The versatile Expert II Series sets a new benchmark for value, offering high accuracy and reliability at an unbelievably affordable price.

The PCB Engraver is supplied with operating software incorporating Gerber and DXF import facilities. The PCB engraver is ideal for cutting and engraving a range of resistant materials, including copper board, plastic and acrylic. • Powerful operating software that is simple to use and allows multiple design to be made at once • High speed spindle motor and floating head • Basic tools and depth-setting device • Installation and Instruction guides • Outlet for dust extraction • Sacrificial Table • USB Connection Optional Equipment: CAD, CAM and/or PCB design software, such as Denford’s QuickCAM 2D Design, will be required in order to make the files required for machining (CNC G-Code or Gerber).

Mild Steel Rod 8mm diameter, length 1500mm.

Mild Steel Flat Bar 10 x 3mm, length 1500mm.

Mild Steel Flat Bar 25 x 3mm, length 1500mm.

Mild Steel Flat Bar 30 x 3mm, length 1500mm.

Mild Steel Flat Bar 12 x 3mm, length 1500mm.

Mild Steel Rod 3mm diameter, length 1500mm.

Tin/Bismuth low temperature casting alloy which has a melting point of 138°C, this is an ideal material for students to practice casting techniques and processes to make items such as busts or figure heads. Being non-toxic and totally re-useable it is an ideal material for schools. Due to the melting point temperature, wooden patterns or plaster of paris moulds can be used. (Pack 4 Tinsmans Sticks).Suitable for the low temperature casting system. Sn 43% / Bi 57%

Mild Black Steel Flat Bar 50 x 3mm, length 1500mm.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 305mm, length 10m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 305mm, length 10m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 200mm, length 50m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 305mm, length 10m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 500mm, length 10m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 500mm, length 10m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 305mm, length 10m.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 305mm, length 10m.

Copper Flat Bar 12.70 x 3.17mm length 1m.

Mild Steel Square Bar 5mm square, length 1500mm.

Mild Steel Square Bar 10mm square, length 1500mm.

Outdoors it has a lifespan of approximately 3 years. Designs may be cut out with CAD/CAM cutter/plotters such as 180-791. Vinyl is adhesive - width 200mm, length 50m.

Brass Rod 6mm dia length 1.5m.

Its composition allows the overlaying of PS Film directly on PS Film, or Flock on PS Film, so offering an endless blend of colours and effects. Key features • Ideal for multi layering • PVC Free transfer vinyl • Matt reflection free surface • Self-adhesive backing for easier weeding and application • Suitable for Cotton, polyester and poly-cotton blends • Hot Peel Due to the many different base materials on the market, the heat temperature given is for guidanceonly. Dimensions:500mm x 1000mm Temperature: 150°C Time: 15 sec Pressure: 15 sec at low pressure

Key features: • Robust cast iron construction • Belt and pulley Drive - 4 speeds • Rack and pinion table raising mechanism • Integral easy to use depth stop • High quality induction motor • T slot table with centre hole • Slotted base • Tilting table • Integral high intensity LED work light • CE Approved Specification: Drilling Capacity: 3-16mm Spindle: 2MT Spindle Speed: 480,820, 1390, 2300rpm at 50Hz Spindle Travel: 110mm Column Diameter: 75mm Table Size (DxW): 225mm x 235mm Power reqirements: Single phase (230V) Power consumption: 0.375kW Dimensions: Height: 900mm Width: 345mm Depth: 670mm Weight: 94kg

THE ROUTER 2600 PRO COMES AS STANDARD WITH: • VR CNC Milling Operating Software (PC not included). • Aluminium T Slot Table. • Installation and Instruction Manuals. • Outlet for Dust Extraction System. • Workholding Clamps. • USB Connection. OPTIONAL EQUIPMENT INCLUDES: 5 Station Automatic Tool Changer, Vacuum Bed, F1 in Schools Car Manufacturing Fixture, 4th Axis Programmable Rotary Fixture, 3D Scanning Attachment, Dust Extraction Unit and Universal Machine Bench. RECOMMENDED SOFTWARE PROGRAMS All software necessary to control the Router 2600/Router 2600 Pro is included. Also included is a seat of QuickCAM 2D Design - an easy to use 2D CAD package. • For 2D Designs - will link to packages able to export 2D dxf files such as QuickCAM 2D Design, TechSoft Design Tools - 2D Design, CorelDraw etc. • For 3D Designs - will link to packages able to export STL files such as Pro/DESKTOP, ArtCAM and Autodesk Inventor, SolidWorks etc. when used in conjunction with QuickCAM Pro. Available with 5 Station Automatic Tool Changer. The F1 in schools package: DESIGN: SolidWorks Education Edition - 3D Design, Drafting & Simulation Software. QuickCAM Pro Advanced Milling/Routing CAM software (site licence). ANALYSE: Virtual Reality Wind Tunnel (VRWT) Software (single licence). MAKE: CNC Machine Options • Router 2600/Router 2600 Pro (Metal Cutting) • Compact 1000 Pro (Metal Cutting) • MRC 40 Car Manufacture Fixture F1 in Schools Car Manufacturing Fixture for both Bloodhound SSC & Formula One Class cars. Consumables - Bloodhound SSC & Formula One Class Cars Formula One Class Balsa Wood Blanks - Pack of 20. Fusion Wheels - Black - Pack of 100. Screw Eyes 1” - Pack of 100. Long Axles - 65mm - Pack of 100. Straw Wheel Spacers - Pack of 500. Washers - 4mm - Pack of 100. Decal Stickers - Pack of 25 sheets. Paint Stand. Bloodhound SSC Class Balsa Wood Blanks - Pack of 20. PX Wheels - Rear - Black - Pack of 100. LX Wheels - Front - Black - Pack of 100. Screw Eyes 1/4” - Pack of 100. Short Axles - 43mm - Pack of 100. TEST: Scout Wind Tunnel. Fog Maestro Smoke Generator including 1Ltr. Fog Fluid. RACE: Elevated Race Track - 25m track. F1 Race System - x1 Start & Finish Gate, x2 Launch Triggers, x2 Launchers, x1 Power Supply, x1 Control Box, Race Time Management System. 8 Gram Competition Cartridges (pack of 120).

The TS1B bench drill has a 13mm drilling capacity, 2 MT spindle and 4 speed operation. It is supplied with a Silverflame BT2 telescopic chuck guard. Key features: • Requires a single phase supply and 10A type C breaker at board • Integral footstop • Robust cast iron construction • Belt and pulley Drive - 4 speeds • Rack and pinion table raising mechanism • Integral easy to use depth stop • High quality induction motor • T slot table with centre hole • Slotted base • Tilting table • Integral high intensity LED work light • CE Approved

The TS440 delivers consistently accurate results with its ceramic guide system, which is fully guarded (adjustments are made through the guard). When installed with the interlocked TSFL Bandsaw Dust Extractor (998-036 only) wood dust is removed from the cutting blade and from the machines dust port below the table. Key features: • Space Age Laguna Ceramic Upper And Lower Roller Blade Guides • Self Releasing Kick Stop • Blade Tension Indicator • Key Locked Security System On Doors And Isolator • Manufactured In Italy For Consistency And Quality • Electro-Mechanical Motor Brake • 240 Volt Single Phase Specification: Wheel dia.: 440mm Blade Speed: 1600 m/min Motor hp: 2hp Cutting Height: 320mm Cutting Width: 410mm Table Size: 420 x 580mm Blade Width: Min:3650mm Max:3700mm Overall Dimensions (W x D x H): 830 x 560 x 1860mm Net Weight: 200kg Dust Extraction Outlet: Two 120mm Diameter ports

The TS540 delivers consistently accurate results with its ceramic guide system, which is fully guarded (adjustments are made through the guard). When installed with the interlocked TSFL Bandsaw Dust Extractor (998-036 only) wood dust is removed from the cutting blade and from the machines dust port below the table. Key features: • Space Age Laguna Ceramic Upper And Lower Roller Blade Guides • Self Releasing Kick Stop • Blade Tension Indicator • Key Locked Security System On Doors And Isolator • Manufactured In Italy For Consistency And Quality • Electro-Mechanical Motor Brake • 240 Volt Single Phase Specification: Wheel dia.: 540mm Blade Speed: 1600 m/min Motor hp: 3hp Cutting Height: 350mm Cutting Width: 520mm Table Size: 520 x 720mm Blade Width: Min: 4190mm Max: 4270mm Overall Dimensions (W x D x H): 870 x 620 x 1970mm Net Weight: 240kg Dust Extraction Outlet: Two 120mm Diameter ports

These drills have dedicated push button controls and all pedestal drills are fitted with a suitable foot operated emergency stop. The Woodpecker complies fully with the European Machinery Directive and also with BS 4163:2014 “Health and Safety for Design and Technology in schools and similar establishments"". Key features: • Aluminium drive pulleys • Wide range of spindle speeds • Motor power transmitted through two V-Belts • Depth stop and scale indicator • Fitted with keyless chuck for hand operation • Precision chuck arbor • Rack and pinion table raising mechanism • Cast Iron control handle with soft grips • Thick wall drill column • Working table with T-Grooves and full 360 degree rotation • Cast iron base with T-Grooves Safety features: • Microswitch on belt guard • No-volt overload push-button starter • Dedicated Push Button Controls • Emergency stop • Large adjustable telescopic chuck guards • All pedestal drills fitted with foot emergency stop • Ratchet table adjustment • Lockable table • Low noise level

This official F1 Model Block measures 223mm x 65mm x 50mm with a consistent weight of 112grams and contains a pre-drilled hole for the CO2 cartridge. This pack contains 10 model blocks. This will be the only material accepted at the F1 in Schools World Finals commencing in 2015. This new block is grain free, has a consistent weight and density, machines very well and is easy to paint.

The universal bench comes with wheels, anti-vibration pads, storage cupboard, tooling drawer and is suitable for both machines. Size: (HxWxD) 780 x 1270 x 750mm. Colour: Grey. The integrated dust extraction unit is an optional extra, please see below for details. With recessed top

Computer Support Extension - Optional Extras for 540-172/1721

Both STL files and image files can be imported into QuickCAM Pro, and a comprehensive set of machining plans can be used individually or in combination to produce complex 3D surfaces and lithophanes. 12 machining plans use individually or in combinations: • 3 Roughing Plans. • 6 Finishing Plans. • 3 Fine Finishing Plans Each plan can be customised or used with default values. Any number of plans can be used to produce the final part. Different cutters can be used with each plan. Simulation mode can be toggled on or off for easy viewing. Custom boundary feature allows selected area to be machined. Viewer and simulation colours can be selected and changed. Finished models can be rendered in custom materials. Intelligent scaling fits model into billet or billet around model. Comprehensive “show me” files to provide Help options SUPPORTED INPUT FORMATS 3D Stereo Lithography*(STL) files. *Used by Pro/DESKTOP, ArtCAM, Autodesk Inventor and Solid Edge. AutoDesk 3D Studio Files (3DS). SYSTEM REQUIREMENTS IBM or 100% Compatible PC, Pentium III, 1Ghz, 512MB RAM, 200MB Free Hard Disk Space, Microsoft Windows XP; NT; 2000; Vista; Windows 7, CD-ROM Drive, OpenGL 3D Accelerator Graphics Card with 128MB RAM supporting at least 1024 x 768 screen resolution. CNC Machines require USB Connection

Tooling package contains: 60 Deg V Cutter; 1/8"" 2 Flute cutter 1/4"" 2 Flute cutter 1/8"" Ball Nose cutter 1/4"" Ball Nose cutter

THE ROUTER 2600 PRO COMES AS STANDARD WITH: • VR CNC Milling Operating Software (PC not included). • Aluminium T Slot Table. • Installation and Instruction Manuals. • Outlet for Dust Extraction System. • Workholding Clamps. • USB Connection. OPTIONAL EQUIPMENT INCLUDES: 5 Station Automatic Tool Changer, Vacuum Bed, F1 in Schools Car Manufacturing Fixture, 4th Axis Programmable Rotary Fixture, 3D Scanning Attachment, Dust Extraction Unit and Universal Machine Bench. RECOMMENDED SOFTWARE PROGRAMS All software necessary to control the Router 2600/Router 2600 Pro is included. Also included is a seat of QuickCAM 2D Design - an easy to use 2D CAD package. • For 2D Designs - will link to packages able to export 2D dxf files such as QuickCAM 2D Design, TechSoft Design Tools - 2D Design, CorelDraw etc. • For 3D Designs - will link to packages able to export STL files such as Pro/DESKTOP, ArtCAM and Autodesk Inventor, SolidWorks etc. when used in conjunction with QuickCAM Pro.

Universal machine bench for Denford Turn 270, includes computer extension.

A compact 3 axis CNC Router with totally enclosed interlocking guard, suitable for all levels of education and training. The Compact 1000 Pro is ideal for cutting a range of resistant materials such as hard and soft wood, plastic, modelling foam, acrylic and prototyping materials, as well as non-ferrous metals. THE COMPACT 1000 PRO COMES AS STANDARD WITH: • VR CNC Milling Operating Software (PC not included). • Aluminium T Slot Table. • Outlet for Dust Extraction System. • Workholding Clamps. • I nstallation and Instruction Manuals. • USB Connection. OPTIONAL EQUIPMENT INCLUDES: Vacuum Pads, F1 in Schools Car Manufacturing Fixture, 4th Axis Programmable Rotary Fixture, 3D Scanning Attachment, Universal Machine Bench and Dust Extraction Unit. RECOMMENDED SOFTWARE PROGRAMS All software necessary to control the Compact 1000 Pro is included. Also included is a seat of QuickCAM 2D Design - an easy to use 2D CAD package. • For 2D Designs - will link to packages able to export 2D dxf files such as QuickCAM 2D Design, TechSoft Design Tools - 2D Design, CorelDraw etc. • For 3D Designs - will link to packages able to export STL files such as Pro/DESKTOP, ArtCAM and Autodesk Inventor, SolidWorks etc. when used in conjunction with QuickCAM Pro.

• Vacuum flow rate - 8m3 per hour • Vacuum level - 85% - 8.5 tonnes per m2 • No of ports/format - one port, desk top plywood frame • Standard bag size - one bag @ 1300mm x 2500mm • Maximum bag size - two bags @ 1300mm x 3000mm This comes with a bag kit whic consists of: 1 x 1300mm x 2500mm, 300micron polyurethane bag 2 x sets of plastic closure strips (to hold bag closed at each end) 1 x plastic round bag connector 1 x 8mm push-fit adaptor (which screws into the bag connector) Note: There is a small bag of fittings placed in the top of the tube containing the bag.

The Hegner Multicut 2S is a our popular mid range scrollsaw with an aluminium table which can tilt up to 45° (right hand side) and 12° (left hand side). It has an impressive throat depth of 460mm and Hegner's qucik tension release. All of our Hegner scrollsaws have these key features & benefits: Superior build quality The superior build quality means that Hegner scrollsaws will survive the rigours of school use providing many years of running. Expertly engineered to reduce vibrations, causing less stress on moving parts. Quick blade changes The quick clamp blade system makes it very easy to change a blade when required. The real benefit comes when doing piercing work. The blade can be quickly released, fed through another part of the workpiece and clamped up again. 3-Year warranty Hegner’s quality is backed up by a 3-year warranty for complete peace of mind. Mobile options Hegner scrollsaws are perfect for a mobile bench setup using our Akira™ solution, meaning easy installation and fully integrated extraction. This is the variable speed version of the Multicut 2S which allows you more control when cutting different material types and thicknesses. A fixed speed version is also availabe (HM-2S). Hegner EDU saws are fitted with No-volt overload release switches and hold down arm & guards as standard. Each Hegner Multicut 2S Scrollsaw is supplied with the following: 1 x Pack of blades with 1 doz each grades 1,5,9 for wood cutting, 1,5,9 for metal cutting and 4 machine coping saw blades 1 x Clock key for blade changing 2 x Blade Clamps fitted in machine 2 x Blade Clamps spare 1 x Quick change blade clamp for quick blade change when pierceworking 1 x Plastic table insert for fine cutting 1 x Toolkit including 2 x Hex (Allen) keys and 1x Tommy Bar

The Hegner Multicut 1 is a our entry level scrollsaw with a strong practical design and powerful motor. It has an aluminium table which can tilt up to 45 (right hand side) and a throat depth of 355mm All of our Hegner scrollsaws have these key features & benefits: Superior build quality The superior build quality means that Hegner scrollsaws will survive the rigours of school use providing many years of running. Expertly engineered to reduce vibrations, causing less stress on moving parts. Quick blade changes The quick clamp blade system makes it very easy to change a blade when required. The real benefit comes when doing piercing work. The blade can be quickly released, fed through another part of the workpiece and clamped up again. 3-Year warranty Hegner’s quality is backed up by a 3-year warranty for complete peace of mind. Mobile options Hegner scrollsaws are perfect for a mobile bench setup using our Akira™ solution, meaning easy installation and fully integrated extraction. This is the fixed speed version of the Multicut 1. A variable speed version is also availabe (HM-1V) which allows you more control when cutting different material types and thicknesses. Hegner EDU saws are fitted with No-volt overload release switches and hold down arm & guards as standard. Each Hegner Multicut 1 Scrollsaw is supplied with the following: 1 x Pack of blades with 1 doz each grades 1,3,5,7,9 for wood cutting 1 x Clock key for blade changing 2 x Blade Clamps fitted in machine 1 x Plastic table insert for fine cutting 1 x Toolkit including 2 x Hex (Allen) keys 1 x Tommy Bar

This de-ionised water is recommended for use with the chiller units of water cooled laser cutters to ensure efficient operation with no contaminents. Morris Deionised Water is produced by ion exchange process, which is recognised alternative to distillation. This method requires no external heat and involves passing ""mains"" water through special resins that have an affinity for the organic and inorganic ions present in the water. These ions are attracted to, and attach themselves to the resin and are hence removed from the water. Morris Deionised Water is therefore very low in metal ion content (e.g. iron, copper, manganese), other inorganic ions (e.g. sulphate, chloride etc) and hence has low conductivity.

The Hegner Multicut 2S is a our popular mid range scrollsaw with an aluminium table which can tilt up to 45° (right hand side) and 12° (left hand side). It has an impressive throat depth of 460mm and Hegner's qucik tension release. All of our Hegner scrollsaws have these key features & benefits: Superior build quality The superior build quality means that Hegner scrollsaws will survive the rigours of school use providing many years of running. Expertly engineered to reduce vibrations, causing less stress on moving parts. Quick blade changes The quick clamp blade system makes it very easy to change a blade when required. The real benefit comes when doing piercing work. The blade can be quickly released, fed through another part of the workpiece and clamped up again. 3-Year warranty Hegner’s quality is backed up by a 3-year warranty for complete peace of mind. Mobile options Hegner scrollsaws are perfect for a mobile bench setup using our Akira™ solution, meaning easy installation and fully integrated extraction. This is the fixed speed version of the Multicut 2S. A variable speed version is also availabe (HM-2SV) which allows you more control when cutting different material types and thicknesses. Hegner EDU saws are fitted with No-volt overload release switches and hold down arm & guards as standard. Each Hegner Multicut 2S Scrollsaw is supplied with the following: 1 x Pack of blades with 1 doz each grades 1,5,9 for wood cutting, 1,5,9 for metal cutting and 4 machine coping saw blades 1 x Clock key for blade changing 2 x Blade Clamps fitted in machine 2 x Blade Clamps spare 1 x Quick change blade clamp for quick blade change when pierceworking 1 x Plastic table insert for fine cutting 1 x Toolkit including 2 x Hex (Allen) keys and 1x Tommy Bar

The Hegner Multicut 1 is a our entry level scrollsaw with a strong practical design and powerful motor. It has an aluminium table which can tilt up to 45 (right hand side) and a throat depth of 355mm All of our Hegner scrollsaws have these key features & benefits: Superior build quality The superior build quality means that Hegner scrollsaws will survive the rigours of school use providing many years of running. Expertly engineered to reduce vibrations, causing less stress on moving parts. Quick blade changes The quick clamp blade system makes it very easy to change a blade when required. The real benefit comes when doing piercing work. The blade can be quickly released, fed through another part of the workpiece and clamped up again. 3-Year warranty Hegner’s quality is backed up by a 3-year warranty for complete peace of mind. Mobile options Hegner scrollsaws are perfect for a mobile bench setup using our Akira™ solution, meaning easy installation and fully integrated extraction. This is the variable speed version of the Multicut 1 which allows you more control when cutting different material types and thicknesses. A fixed speed version is also availabe (HM-1). Hegner EDU saws are fitted with No-volt overload release switches and hold down arm & guards as standard. Each Hegner Multicut 1 Scrollsaw is supplied with the following: 1 x Pack of blades with 1 doz each grades 1,3,5,7,9 for wood cutting 1 x Clock key for blade changing 2 x Blade Clamps fitted in machine 1 x Plastic table insert for fine cutting 1 x Toolkit including 2 x Hex (Allen) keys 1 x Tommy Bar

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Quality Hardwood Dowel from sustainable sources. Single length of 25mm diameter, 600mm long. Nominal size ± ½ mm.

Quality Hardwood Dowel from sustainable sources. Single length of 16mm diameter, 600mm long. Nominal size ± ½ mm.

Quality Hardwood Dowel from sustainable sources. Single length of 19mm diameter, 600mm long. Nominal size ± ½ mm.

Black coloured rigid plastic tube with a wide variety of uses, 760mm long.

White coloured rigid plastic tube with a wide variety of uses, 760mm long.

Quality Hardwood Dowel from sustainable sources. Single length of 22mm diameter, 600mm long. Nominal size ± ½ mm.

Quality Hardwood Dowel from sustainable sources. Pack of 10, 4mm diameter, 600mm long. Nominal size ± ½ mm.

Square ABS tube, sizes are nominal due to manufacturing.