TSL

• Machine Type - Medium /Bench or Pedestal • Method of attachment - Secures around depth stop collar using fixing top to suit configuration • Positive Manual latch • Flip up with spring retention • Construction - Aluminium/Nylon with Polycarbonate Vizor which encloses the work area • Operation - Telescopes on contact with work piece, length adjustable vizor Please state collar size when ordering. Maximum chuck dia. for the MT is 63mm / MTS is 70mm.

M2 Min-Max Vertical height: 250-450mm Overall length - enclosed: 475-800mm Overall length - extended: 925-1250mm Please note: We require T-slot size to match this product to your machine.

Spare vizor for BT Drill guard (590-204 & 590-204X). Constructed from scratch resistant polycarbonate.

• Machine Type - Light/Bench or Pedestal • Method of attachment - secures to drilling machine spindle collar • Positive manual latch • Flip up with spring retention • Construction - moulded polycarbonate • Operation - Telescopes on contact with work piece, length adjustable vizor which encloses the work area The maximum collar size for the BT is 70mm (minimum 40mm). Please state collar size when ordering.

• Machine Type - Light/Bench or Pedestal • Method of attachment - secures to drilling machine spindle collar • Positive manual latch • Flip up with spring retention • Construction - moulded polycarbonate • Operation - Telescopes on contact with work piece, length adjustable vizor which encloses the work area Collar size: 64mm

A range of accessories for use with any extractor. Jubilee clips are Kite marked to BS5315 (1991) and the company is licensed to BS EN ISO 9001. Made from mild steel, zinc protected and used for fixing flexible rubber hoses, metal tubes etc. BZP Size 5 Adjustment . 90 - 120mm Adjustment. 3.1/2 - 4.3/4in

A cartridge filter for the Woodvac TS100.

Filter bags for WV150 Pack of 6

Pack of 5 standard poly waste bags. Size 915mm x 812mm (36"" x 32"").

Used for Hegner Multicut scrollsaw and extraction installations to connect a Multicut to a dust extraction system for optimum dust removal.

Contents: LH Turning Tool 12mm Shank RH Turning Tool 12mm Shank Pack of 10 Inserts for LH/RH Turning Tools Parting Off Tool 12mm Shank with 10 Inserts External Threading Tool 12mm Shank with 10 Inserts Boring Bar 8mm Shank with 10 Inserts 5mm Centre Drill 2 Stub Drills (5mm & 10mm) 4 Turret Bushes (2 x 5mm, 8mm & 10mm)

These switches can be mounted conveniently as foot / knee / palm switches and wired into the machine by a competent electrician. • Ingress protection to Ip67 • 1 N/O, 1 N/C contacts (10A) • 5 x PG13 cable entries (1 threaded) • IEC418 tamperproof, UL and CSA approved Dimensions: 94mm x 94mm

Programmable spindle speeds and feedrates make the Turn 270 Pro ideal for cutting a range of resistant materials such as wax, plastic, acrylic, free cutting alloys, aluminum and steel. THE TURN 270 PRO COMES AS STANDARD WITH: • VR CNC Turning Operating Software (PC not included) • QuickTURN 2D Design Software (1 seat) • Quick Change Toolpost and Holder • Manual Self Centring 100mm 3 Jaw Chuck • Installation and Instruction Manuals • USB Connection

• Machine Type - Light /Bench or Pedestal (dedicated to machine make) • Method of attachment - Clips to back pillar • Positive Manual latch or interlock • Side opening • Construction - Mild steel with 4 mm polycarbonate vizor • Operation - Remains stationary allowing depth stop collar and chuck to pass through length adjustable vizor

These holesaws cut perfect holes in a wide variety of materials including wood, chipboard, plywood, non laminated plastics, plasterboard and non ferrous metals. Suitable for use in most variable speed power drills. Supplied in a sturdy case for safe and secure storage. Contains: 12 x Varipitch Holesaws: 16, 20, 22, 25, 32, 35, 38, 44, 51, 64, 70, and 76mm. 1 x 3/8in Arbor (14-30mm). 1 x 7/16in Arbor (32-152mm). 1 x Arbor Adaptor. 1 x 300mm Extension Bar. 1 x Aluminium Case.

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 12mm (6tpi) 6tpi - skip teeth & are best for cutting timber

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 12mm (14tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 6mm (14tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 2845 x 9.5mm (14tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

• Machine Type - Light/ Bench or Pedestal • Method of attachment - Side fixing or clips to back pillar • Positive Manual latch or interlocked • Side opening • Construction - Moulded 5mm polycarbonate body, with 4 mm polycarbonate vizor, adjustable to suit machine depth stop bracket • Operation - Remains stationary allowing depth stop collar and chuck to pass through length adjustable vizor

• Machine Type - Light to medium centre lathes • Method of attachment - Secures to face or top of lathe headstock • Manually adjusted to cover work area. Interlocked • Construction L6 - Cast aluminium and 4 mm polycarbonate visors • Construction L12 & L18 - Mild steel, P.V.C. skirt, 6.6 nylon pivot bushes and 4mm polycarbonate visors • Operation - Hinges to allow access to chuck and work area

315mm Dia, 30mm bore. For accurate sizing and trimming timber and manmade boards. Supplied with standard pinholes including Sedgwick and Scheppach.

315mm Dia, 30mm bore, 14mm pinhole. General purpose giving superior finish for both ripping and crosscutting applications. Supplied with standard pinholes including Sedgwick and Scheppach.

With a melting point of 240°C, this is an ideal material for teachers to demonstrate casting techniques and processes to make highly detailed items such as jewellery, tankards, coasters, place mats, trays etc. Being non-toxic and totally re-useable it is an ideal material for schools. *The weight of one stick is approx 1kg Alloy conforms to BS EN 611-1:1996 Alloy 3 Lead Free Pewter.

Mild Steel sheet 500 x 1000 x 1mm.

With snap connectors.

These LED's are sold singly.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

Our cast acrylic is suitable for laser cutting, CNC machining, line bending and blow moulding. It can also be cut using a plastics cutter or on a bandsaw or scrollsaw. Often used for fabrication, laser engravings, noticeboards and signage and attractive displays. It is manufactured to a high standard and provides impact and UV resistance, good thermal stability and low water asorption. It is very easy to work with and cast in particular is recommended for CNC machining. We also have bulk packs available which save you even more money per sheet when buying larger quantities. Please note that due to the way cast acrylic is manufactured, the sheet thickness is nominal and may vary slightly +/- 18%.

• Quality virgin grade material (can be used with food) • Convenient sheet size to fit specified vacuum forming machines • Strong bright colour

For Craft & Supercraft chucks.

This set enabls the creation of a variety of profiles, grooves and mouldings in softwoods, hardwoods, MDF or plywood. Tungsten Carbide tips ensure long life and the sturdy aluminium storage case provides a safe place to store the bits when they are not being used. Contents: One of each Dia Depth Straight Cutter 5.0mm 12mm Straight Cutter 6.0mm 20mm Straight Cutter 8.0mm 20mm Straight Cutter 10.0mm 20mm Straight Cutter 12.0mm 20mm Straight Cutter 14.0mm 20mm Straight Cutter 16.0mm 20mm Straight Cutter 18.0mm 20mm Straight Cutter 20.0mm 20mm Dovetail Cutter 12.7mm 13mm 90 deg V cutter 9.5mm 9mm 90 deg V cutter 12.7mm 9mm Core Box 3.2mm Rad 6.0mm 6mm Core Box 6.35mm Rad 12.7mm 10mm Classical Pannel 12.7mm 9mm Guided Flush Trimmer 12.7mm 13mm 25 deg Guided Chamfer 16.0mm 9mm 45 deg Guided Chamfer 32.0mm 13mm Roman Ogee 4mm Rad 25.0mm 12mm Guided Rabbeting Cutter 28.6mm 13mm Guided Cove 6.35mm 22.0mm 12mm Guided Cove 9.5mm 28.0mm 12mm Guided Rounding over 3.2mm Rad 15.0mm 7mm Guided Rounding over 6.35mm Rad 22.0mm 12mm Guided Rounding over 7.9mm Rad 25.0mm 14mm Guided Rounding over 9.5mm Rad 28.0mm 14mm Guided Beading 3.2mm Rad 16.0mm 8mm Guided Beading 6.5mm Rad 22.0mm 12mm Guided Beading 7.9mm Rad 25.0mm 14mm Guided Beading 9.5mm Rad 28.0mm 15mm

BOSCH PSS 200A Consumer model. • Orbit diameter 2.0mm • Base plate size 93x185mm • Velcro fixing system • Integrated dust extraction facility • Ergonomic design allows for both single and two handed use • No load speed 24,000rpm • Soft Grip

Technical data Power input 1.200 W Power output 650 W Toolholder (supplied) 6 mm 8 mm 1/4"" No-load speed 11.000 28.000 rpm Maximum router cage stroke 55 mm Machine weight 3,4 kg Functions Spindle lock Bosch SDS for template guide Bosch Speed Electronic Dust extraction Softgrip

Bagpress MiniPressMkII - BPEL02 The level of vacuum achievable is 70% which equates to around 620kg per m2. Vacuum flow rate - 0.4m3 per hour Vacuum level - 85% - 8.5 tonnes per m2 Standard bag size - one bag @ 800mm x 1300mm Maximum bag size - 1300mm x 1300mm

A smart easycare apron supplied in a range of colours without pockets. 100% cotton Size: 35"" x 24''

• High quality blades • Suitable for all general purpose cutting of wood, plastics and metal • High carbon steel with hard teeth & flexible back to ensure long cutting life 3580 x 12mm (10tpi) 10 & 14tpi - regular teeth, good for thin sections of timber and plastics

Red 2.85mm PLA 3D Printer Filament High quality 3D printer filament suitable for any Fused Filament Fabrication 3D printer that supports third party material.

Low cost momentary (non-locking) action panel mounting push to make switches. Supplied with fixing nut & washer 7mm cut out. External Diameter:10mm External Length / Height:28mm

Evo-Stik rapid set syringe application. 25ml.

Duct Tape 50mm wide 50 metres in length.

Great roundness and consistency, PLA is Poly-Lactic-Acid, a biodegradable polymer that has a low melting point. It is an amazing material to print with and you can print at very high speeds when using this material.Ultimaker filaments have endlessly been tested to ensure they are up to the job: only the best make the grade. Prints come as intended time and time again.Ultimaker PLA is really easy to print with, it's reliable, gives good surface quality and it's made from renewable sources, so it's biodegradable too. It also works perfectly with Cura material profiles. • If you want to easily achieve high resolution prints • Printing concept models and prototypes when aesthetics and fine details are key • When you're casting metal parts through lost PLA casting • It's perfect for printing in education or in the office, thanks to low ultrafine particle emissions • A heated bed isn't necessary, it works with glue and blue tape as well • PLA isn't suitable for medium temperature applications (50°C +) or long term outdoor usage. ABS is a better material for high temperature applications and CPE for outdoor usage.

Standard brushes are a better quality and are sold singly. Economy brushes are mixed bristle, and are sold in dozens.

Twin-thread silver zinc-plated countersink PZD screws. Sizes: 5/8"" x 4, 3/4"" x 4, 1"" x 6, 1-1/4"" x 6, 1"" x 8, 1-1/4"" x 8, 1-1/2"" x 8, 1-1/2"" x 10, 2"" x 10, 2-1/2"" x 10, 3"" x 10. 780pce (approx).

Pan head self-tapping Pozidriv screws. Sizes: 3/8"" x 6, 1/2"" x 6, 3/4"" x 6, 5/8"" x 8, 3/4"" x 8, 1"" x 8, 1 1/4"" x 8, 1/2"" x 10, 3/4"" x 10, 1"" x 10 and 1 1/4"" x 10.

Specially made for dowel joints, the flutes allow air to escape and the glue to flow evenly. Specifications: Diameter - 6mm Length - 30mm

• Perfect way to get started with programming and hardware interaction • No soldering required • All parts are included to build 6 projects • Small prototype breadboard included • Projects: Dice, Buzzer, Theremin, Miniature Steady Hand Game, Fruit Keyboard, Traffic Lights Kit contains: 1 x micro:bit, 1 x piezo buzzer, 1 x 170 pin breadboard, 1 x 10mm red LED, 1 x 10mm yellow LED, 1 x 10mm green LED, 1 x battery case with AAA batteries, 1 x set of crocodile clip wires and 0.5mm micro USB cable

Supplied with a solid refractory hearth with robust side and rear heat shields, the DS400 complies with British Gas standards and is a fully failsafe system. All sequences are visually displayed using neon indicators. On start-up the gas train, hoses and torches are tested for escaping gas. Leaks from any component will result in a continuously illuminated red neon and the main flow of gas will be prevented from entering the system. • Perfect for use in school design technology workshops or industry use, i.e. jewellery workshops. • Easy-to-use RF80 brazing torch allows one-hand operation • A solid refractory hearth with robust side and rear heat shields • A fully fail safe system, compliant with British Standards • All sequences are visually displayed using neon indicators

The forge has a single phase whisper quiet integral fan to provide the air supply and takes only 15 minutes to reach a working temperature. It can reach a temperature of 1,500°C. It has a 340mm diameter working area and can work up to 50mm steel bar. The ceramic chip technology minimises surface scale formation. The forge has a single phase whisper quiet integral fan to provide the air supply with fail safe auto ignition for the gas supply. The forge has a cast iron base for a long maintenance free life. • Push-button no-volt release starter • Requires manual restart after power failure • Ceramic Hearth • Automatic safety check of controls and air fan • Full manual control of hearth conditions • Whisper quiet air blower fan • Indicator status lights • Gas non-return valve • 12.5kg of ceramic chippings • Operation / Instruction manual • Side and rear heat shields • Rake iron • Can be run on either Natural Gas or LPG bottled gas

The forge has a single phase whisper quiet integral fan to provide the air supply and takes only 15 minutes to reach working temperature. It can reach a temperature of 1,500°C. It has a 340mm diameter working area and can work up to 50mm steel bar. The ceramic chip technology minimises surface scale formation. The brazing hearths both have an area of 0.23 square metres with heavy duty refractory bases. One or both of the RF80 brazing torches, which deliver up to 80,000BTU of heat output, can be replaced by Flamefast RF10 jewellery torches for fine work. All Flamefast RF torches have a single hand-wheel control to give ease of flame control and a constant flame pattern over the range of flame sizes. The torches are ignited electronically. • Especially useful where space limitations are a consideration • Unit consists of a ceramic chip forge and two brazing hearth usually equipped with 2 Flamefast RF80 brazing torches • Can be run on either Natural Gas or LPG bottled gas • Shown with Varivac extraction canopy

Tilt & pour feature provides safer metal pouring and extended crucible life. Standard equipment: • Piezo ignition and flame failure device • Super efficient insulation • A10 capacity crucible pot • Crucible lid • Tilt handle • Pouring gauge • Degassing plunger • Skimming ladle/dross lifter • Safety burner • Cut-out prevents burner from operating when the drum is tilted • Operation/Instruction manual

All of our laser packages are supplied complete with everything required for a complete educational solution including recirculatory extraction unit, connection kit, design software. We also provide flexible training solutions with onsite installation and training or additional training sessions should you require a 'top-up.' • Popular all round laser engraver with stable and satisfactory performance • Intuitive control panel allows easy operations • Low maintenance motion system • Emergency button and key-switch add an extra layer of safety WARRANTY INFORMATION 24 months machine and laser tube warranty. Additional 12 months warranty on machine and laser tube is available.

Polylactic acid (PLA) is a biodegradable thermoplastic derived from renewable resources.

Printer Compatibility • METHOD 3D Printer • METHOD X 3D Printer* • METHOD X Carbon Fiber 3D Printer Extruder Compatibility • Support 2 Extruder

Pre-Filter Labyrinth F6 for Purex 300i fume extractor.

Create eye-catching graphics at speeds of up to 1020mm/second (40.2 inches/second). It has 500g of cutting force a tracking ability of five metres (16.4 feet). Puma IV is powered by a digitally controlled servo system and the Accu-alignment system II which comes as standard allows for precise contour cutting of digitally printed graphics by detecting the registration marks. Enhanced AAS II Contour Cutting System The Puma IV series features a standard Automatic-Aligning System(AAS II) to guarantee precise contour cutting by detecting the registration marks on digitally produced images. Includes Great Cut software 1-year on-site warranty

The Cameo 4 has had a complete make over, new aesthetic, sliding lid and a compact design make it the prefect desktop cutting system for home or small business. The Cameo 4 provides the user with more cutting functions than ever before with inclusion of 3 brand new blade types: • Rotary Blade • Kraft Blade • Punch Tool With wireless Bluetooth connectivity and a familiar 12″ cut width the Cameo 4 is the perfect desktop cutting tool for the serious crafter, small business or model maker.

All of our laser packages are supplied complete with everything required for a complete educational solution including recirculatory extraction unit, connection kit, design software. We also provide flexible training solutions with onsite installation and training or additional training sessions should you require a 'top-up.' • QSM (Quality Speed Mode) maintains 100% engraving quality while operating at maximum speed • Patented SmartACTTM motion control technology increases your productivity by reducing ramping process and job running time • Drag and engrave feature assures remarkably easy and fast set-ups • High speed DC motor runs up to 80ips for precise and rapid movement of the laser carriage • Reliable DuraGuide motion system with reinforced Kevlar belt delivers superb output quality • This machine is fi tted with the Smart Guard Fire Alarm and auto-cut out on extraction failure as standard WARRANTY INFORMATION 3 year machine warranty, 15 month tube warranty

Combined HEPA/Gas filter for BOFA AD1000/iQ

Deep pleat pre-filter for AD1000/iQ

PVA (Polyvinyl Alcohol) is a water soluble support material for multi-extrusion 3D printing. With a good thermal stability, Ultimaker PVA is ideal for printing complex models that require supports for large overhangs, deep internal cavities, and intricate geometries. Designed for a seamless 3D printing experience, our PVA provides good adhesion to both PLA and Nylon. • Good thermal stability resulting in better degradation resistance compared to other PVA filaments • Less moisture sensitive than other PVA filaments • Great adhesion to both PLA and Nylon • Safe dissolution in tap water (no harmful chemicals required) • Biodegradable with no hazardous by-products PVA allows to effortlessly create complex 3D prints by building water soluble support structures. 1. Submerge. Put your 3D print in cold or warm water depending on the build material. 2. Rinse. After PVA supports are dissolved, rinse the 3D print to remove any excess PVA solution. 3. Dry. Let the 3D print dry and apply additional post processing to the build material if necessary. As a water soluble support material, Ultimaker PVA empowers engineers and designers to create highly detailed surfaces and complex moving mechanical parts in just one run. Coupled with the right build materials and our proven material profiles in Cura for Ultimaker 3, our PVA opens up a whole new world of opportunities for intricate designs and versatile applications.

• A constant temperature to prevent warping (detachment of the part) and facilitate 3D prints that require difficult-to-print materials (ABS, PC) • The air is replaced using a professional fan and HEPA filter • No more draughts during printing • The cover can be installed and uninstalled easily without damaging the printer. No screws or drill needed; simply clip on the kit • A latch closes the door and protects prints from any outside access. This latch is particularly useful in an educational context to protect high-temperature parts • No odour or smoke escapes from the printer thanks to the HEPA filter which has a working life of between 600 and 1200 hours depending on the materials and print settings

The Ultimaker S3 is a complete production system you can depend on in the office or studio. With advanced features to ensure a reliable printing experience, it's still simple to use thanks to its award-winning touch interface and seamless software integration. • Dual extrusion with a build volume of 230 x 190 x 200 mm (9 x 7.4 x 7.9 inches) • Down to 20 micron (0.001 inch) layer resolution • Open filament system, compatible with glass and carbon fibre composites • Dual filament flow sensors notify you if material runs out • 4.7-inch touchscreen interface Winner of iF Design Award 2019

For high precision cutting of medium and heavy duty materials.

With snap connectors.

Low cost batteries with a shelf life of 2 years and are suitable for low drain applications. Pack of 2.

4mm black stackable plugs pack of 5

4mm red stackable plugs pack of 5

5mm ultrabright white LED, pack of 10

5mm ultrabright Red LED, pack of 10

Pack of 10 minature LDRs

Simple push to make switch - pack of 10

Lever toggle switch SPST, pack of 10

Pack of 10 buzzers with leads 6V

Carbon film resistors pack 1000

Pack of 10 mains fuses

This heavy duty A3 laminator features a double heating system utilising a hot roller and plate, providing high quality lamination. It also features clear instructions on the front of the product and a digital display for precise settings. With an operating speed of 465mm per minute, this product also features an anti-jam reverse function, helping to keep your workstation running smoothly.

Ideal for use with wood chisels. Size: 115mm

Reduces the standard forming area of the C R Clarke 750 vacuum former from 482 x 432mm to 228 x 216mm.

Pack of 10 assorted diameters, 2 each of 5, 6, 8, 10 and 20mm.

Nine speeds Vee belt drive Head tilts left to right, calibrated to 45° 360° rotation on horizontal axis One shot lubrication system to slideways and leadscrews to ensure prolonged machine life Choice of spindles - R8 or 3MT • Choice of either metric or imperial leadscrews • Traditional design with elevating knee, supported on double dovetail vee ways to ensure positive alignment • Tapered gibs to X, Y and Z axes • Rack and pinion feed and calibrated fine feed to quill • Locks to X, Y and Z axes • Interlock belt guard • Cabinet stand included. •New! LED lighting

The rip fence is aluminium section allowing for two working positions (ripping and angled ripping). It is fixed to a cast iron mounting bracket for rigidity and has integral micro adjustment. A telescopic extension arm is fitted to the cross cut fence for setting the timber stop. The 620mm Cross Cut Table is designed for cutting mitres and compound angles, end trimming, squaring, dividing and trimming. It has a maximum depth of cut 105mm @ 90° and 76mm @ 45°, double sided saw guard with dust extraction outlet, enclosed drive mechanism. Supplied with an anti kick saw blade. Thermal overload, no-volt release switch, lock off emergency stop switch and foot operated foot switch are fitted as standard. Fitted with keyswitch.

The hand-wheel is made from an ergonomically designed one piece casting for comfort of use whilst also providing additional weight to the headstock. These models come with 12 speeds making them ideal for drilling metal as well as wood. MT2 arbor No volt release switch Complete with 16mm chuck We strongly recommend footstop switches are added to these machines to comply with BS4163:2007.

It features 140rpm wheel speed, force-fed recirculatory coolant systems and a tool holder that accepts up to 60mm wide blades. The centre swivel arm has fine adjustment control to ensure that the tool edge and grinding wheel remain in perfectly flat contact. Safety features include a no-volt overload pushbutton starter, large foot stop switch and an automatic safety cut-out if the front door is opened whilst the machine is switched on. KEY FEATURES • Controlled 140rpm wheel speed • Force-fed recirculatory coolant system and anti-spill tray • Integral oil reservoir with filter • Tool holder for blades up to 60mm wide • Radius gouge attachment • Centre swivel arm with vernier adjustment

Fixing kit for 7inch vices.

The head itself is counterbalanced by a weight, giving fingertip control to the rise and fall and eliminating the breakages associated with spring type mechanisms. Its 1.1kw industrial fan cooled motor provides ample power for continuous duties and is fitted with a fully guarded adjustable chuck. Unlike a collet type system the chuck holds the auger firmly round its circumference, true to the centre line of the chisel, securing longer tool life and better cutting capability. The table has longitudinal and lateral movement on a single handwheel, not only for ease of operation, but also for more precise positioning: lateral adjustment of the table being better controlled by a central screw. The angled timber clamp is adjustable on a tee slot, to give a maximum timber width of 200mm. Coupled with the height adjustable chisel head which can give a maximum timber height of 255mm underneath the chisel, the Sedgwick 571 has exceptional capability. For repetition work there are longitudinal stops along the front of the table, a marking out rail complete with turnover stop along the rear; and 2 position depth stop for haunching. The switchgear has no volt release, thermal overload protection, and a mushroom headed stop button.

This bench is fitted with a beech top. Standard sizes 1800mm long, 760, 810 or 910mm wide and 810 or 860mm high. A maximum of 4 metalwork vices can be fitted (sold separately).

Replacement filter (spring type set) for the TSUB dust extractor.

Replacement main filter for the TSMB dust extractor.

Replacement after filter for the TSMB dust extractor.

Replacement filter for the TSPL dust extractor.

Replacement filter for the TSHS dust extractor.

Includes filter moitoring system to help identify when filters need replacing. Large dust collection tray and filter shaking mechanism.

Metal framed bench with a beech top and fitted cupboards underneath, a maximum of 4 metalwork vices can be fitted (not included). HxWxD: 860 x 810 x 1800mm.

The 6x 68mm deep drawers provide ample space for A1 size paper and slide on easy-glide runners to ensure smooth action even on when drawers are heavy with paper or card. Modern bow handles, finished in silver, stylishly complement each drawer providing a sturdy grab point on each drawer when sliding them out and back in. Steel legs, powder coated in a deep charcoal black, neatly frame the drawers beautifully and look superb and also match the black finish on the inside of the drawers. Available in grey, light oak or beech.

Suitable for small power tools. • Single motor • Two stage filtration • Supplied with hose

For use with your RICOH SG 3110DN

Black Sublijet Ink Cartridge for Printers 3110DN & SG 7100DN. Size: 42ml

Cyan Sublijet Ink Cartridge for Printers 3110DN & SG 7100DN Size: 29ml

Magenta Sublijet Ink Cartridge for Printers 3110DN & SG 7100DN Size: 29ml